Journal of Energy Management and Technology

Journal of Energy Management and Technology

Power System Analysis Using The ETAP Software: A Comprehensive Review

Document Type : Review Article

Author
Hamdi Abdi
Electrical Engineering Department, Engineering Faculty, Razi University, Kermanshah, Iran
10.22109/jemt.2024.467452.1518
Abstract
With the increase in population and the amount of energy required, power systems have become more complex and extensive over time. Because of the development of new equipment and modern operation strategies, these system complexities are also continuously increasing. One of the most powerful tools to model, and analyze modern, and complex power systems is Electrical transient analyzer program known as ETAP software that was developed by ETAP, United States. Since the introduction of this software, its different versions were provided, and much research were conducted in power system field by using it. This research for the first time attempts to provide a comprehensive survey on different applications of this simulation tool. For this purpose, after addressing the research conducted using the ETAP software in power system, the classification of its different versions is presented. Then a general survey on addressed references in terms of publication year, publishers, different categories is mentioned. Detailing power system analysis in terms of different studies, and addressing the relevant works of each category is then presented. Furthermore, different case studies used in power system analysis in three categories of practical cases in different countries, standard grids, mainly IEEE systems, and some sample and typical grids are segmented. Ultimately, the work opens new views on the future directions.
Keywords
Arc flash analysis
Battery sizing
Contingency analysis
Equipment sizing
ETAP real-time overview

Subjects

  1. Abdi, H., Profit-based unit commitment problem: A review of models, methods, challenges, and future directions. Renewable and Sustainable Energy Reviews, 2021. 138: p. 110504.
  2. Abdi, H., M. Shahbazitabar, and B. Mohammadi-Ivatloo, Food, energy and water nexus: A brief review of definitions, research, and challenges. Inventions, 2020. 5(4): p. 56.
  3. Shahbazitabar, M., et al., An Introduction to Microgrids, Concepts, Definition, and Classifications. Microgrids: Advances in Operation, Control, and Protection, 2021: p. 3-16.
  4. Abdi, H., A Brief Review of Microgrid Surveys, by Focusing on Energy Management System. Sustainability, 2022. 15(1): p. 284.
  5. Sharifian, Y. and H. Abdi, Multi-area economic dispatch problem: Methods, uncertainties, and future directions. Renewable and Sustainable Energy Reviews, 2024. 191: p. 114093.
  6. Abdi, H. and M. Shahbazitabar, Smart city: A review on concepts, definitions, standards, experiments, and challenges. Journal of Energy Management and Technology, 2020. 4(3): p. 1-6.
  7. Abdi, H., A Survey of Combined Heat and Power-Based Unit Commitment Problem: Optimization Algorithms, Case Studies, Challenges, and Future Directions. Mathematics, 2023. 11(19): p. 4170.
  8. Brown, K., et al. Interactive simulation of power systems: ETAP applications and techniques. in Conference Record of the 1990 IEEE Industry Applications Society Annual Meeting. 1990. IEEE.
  9. Bam, L. and W. Jewell. Power system analysis software tools. in IEEE Power Engineering Society General Meeting, 2005. 2005. IEEE.
  10. Martinez-Velasco, J.A., F. De Leon, and V. Dinavahi, Simulation tools for analysis and design of distribution networks with distributed energy resources. Electrical Power Quality and Utilisation. Journal, 2009. 15.
  11. Shrestha, A., et al. Using hardware and software studies to teach power-system modeling and analysis. in 2009 IEEE Power & Energy Society General Meeting. 2009. IEEE.
  12. Selvan, P. and R. Anita, Revelation for new user to select power system simulation software. Journal of Asian Scientific Research, 2011. 1(7): p. 366-375.
  13. Tang, C. Electrical power system modeling and simulation of large-scale industrial enterprise. in 2011 International Conference on Advanced Power System Automation and Protection. 2011. IEEE.
  14. Al-Sheikh, H. and N. Moubayed. An overview of simulation tools for renewable applications in power systems. in 2012 2nd International Conference on Advances in Computational Tools for Engineering Applications (ACTEA). 2012. IEEE.
  15. Mekhamer, S., A. Abdelaziz, and S. Ismael, Design practices in harmonic analysis studies applied to industrial electrical power systems. Engineering, Technology & Applied Science Research, 2013. 3(4): p. 467-472.
  16. Agrawal, R., S. Bharadwaj, and D. Kothari, An educational and professional simulation tools in power systems and facts controllers-an overview. International Journal of Electrical, Electronics and Computer Engineering, 2013. 2(2): p. 91-96.
  17. Mahmud, K. and G.E. Town, A review of computer tools for modeling electric vehicle energy requirements and their impact on power distribution networks. Applied Energy, 2016. 172: p. 337-359.
  18. Kalair, A., et al., Review of harmonic analysis, modeling and mitigation techniques. Renewable and Sustainable Energy Reviews, 2017. 78: p. 1152-1187.
  19. Mahmud, K., et al., Computational tools for design, analysis, and management of residential energy systems. Applied Energy, 2018. 221: p. 535-556.
  20. Thopil, M.S., et al., A review of grid connected distributed generation using renewable energy sources in South Africa. Energy strategy reviews, 2018. 21: p. 88-97.
  21. Mahmud, K., D. Soetanto, and G.E. Town, Energy management softwares and tools, in Comprehensive energy systems: energy management. 2018, Elsevier. p. 202-257.
  22. R. Gayathri, K.S., S.E.Manoj Kumar, R.Praveen, Evolution Of Etap Software Tool For Power System Studies: a Literature Survey. International Journal of Pure and Applied Mathematics, 2018. 118(4): p. 1-20.
  23. Abass, A., D. Pavlyuchenko, and Z.S. Hussain. Methods Comparison for Optimal Capacitor Placement in Distribution System. in 2020 International Multi-Conference on Industrial Engineering and Modern Technologies (FarEastCon). 2020. IEEE.
  24. Barra, P.H.A., D.V. Coury, and R.A.S. Fernandes, A survey on adaptive protection of microgrids and distribution systems with distributed generators. Renewable and Sustainable Energy Reviews, 2020. 118: p. 109524.
  25. Mehta, S. and P. Basak, A comprehensive review on control techniques for stability improvement in microgrids. International Transactions on Electrical Energy Systems, 2021. 31(4): p. e12822.
  26. Hussen, S., F. Ayalew, and K. Ibrahim. Assessment of Distribution System Reliability and its Possible Mitigations: A Review. in International Conference on Advanced in Management and Technology (ICAMT-2020). 2020.
  27. Braide, S. and O. Kenneth, Improved reliability analysis of electricity power supply to Port Harcourt distribution network. International Journal of Engineering Science Invention, 2018. 7(7): p. 23-36.
  28. Al Hakim, R.R., E. Ariyanto, and Y.Z. Arief, Techno-Economic Study of Substation Electric Power in Indonesia: A Mini-Review. ARRUS Journal of Engineering and Technology, 2021. 1(1): p. 28-32.
  29. Istiyono, Y.P., Analisa Tekno Ekonomi Pembangunan Gardu Induk 150kV Terotomasi Untuk Industri. EPIC (Journal of Electrical Power, Instrumentation and Control), 2020. 3(1): p. 97-106.
  30. Rifal, R., S.B. Utomo, and M. Haddin, Analisis Perhitungan Rugi-Rugi Daya pada Saluran Transmisi Tegangan Tinggi 150 kV Gardu Induk Tambak Lorok–Bawen dengan menggunakan Etap 12.6. 0. Prosiding Konstelasi Ilmiah Mahasiswa Unissula (KIMU) Klaster Engineering, 2020.
  31. Suwardana, I.W., I.P. Sutawinaya, and I.A.R. Wulandari, Studi Analisis Rugi-Rugi Daya pada Penghantar Netral Akibat Sistem Tidak Seimbang di Jaringan Distribusi Gardu KA 1495 Penyulang Citraland Menggunakan Simulasi Program ETAP 7.0. Logic: Jurnal Rancang Bangun Dan Teknologi, 2017. 14(3): p. 157.
  32. Khalid, H. and A. Shobole, Existing developments in adaptive smart grid protection: A review. Electric Power Systems Research, 2021. 191: p. 106901.
  33. Aruna, S., et al., A Comprehensve Review on the Modern Power System Reliability Assessment. International Journal of Renewable Energy Research (IJRER), 2021. 11(4): p. 1734-1747.
  34. Shair, J., et al., Power system stability issues, classifications and research prospects in the context of high-penetration of renewables and power electronics. Renewable and Sustainable Energy Reviews, 2021. 145: p. 111111.
  35. Verma, P.K. and G. Goswami. Power Quality Issues Associated with Smart Grid: A Review. in 2021 10th International Conference on System Modeling & Advancement in Research Trends (SMART). 2021. IEEE.
  36. Shobole, A.A. and M. Wadi, Multiagent systems application for the smart grid protection. Renewable and Sustainable Energy Reviews, 2021. 149: p. 111352.
  37. Buła, D., D. Grabowski, and M. Maciążek, A review on optimization of active power filter placement and sizing methods. Energies, 2022. 15(3): p. 1175.
  38. Kafle, P., M. Bhandari, and L.B. Rana, Reliability Analysis Techniques in Distribution System: A Comprehensive Review. 2022.
  39. Nkosi, N., et al., A review of small-signal stability analysis of DFIG-based wind power system. International Journal of Modelling and Simulation, 2022: p. 1-18.
  40. Ahmad, T., et al., Data-driven probabilistic machine learning in sustainable smart energy/smart energy systems: Key developments, challenges, and future research opportunities in the context of smart grid paradigm. Renewable and Sustainable Energy Reviews, 2022. 160: p. 112128.
  41. Grisales-Noreña, L.F., et al., Optimal Location and Sizing of Distributed Generators and Energy Storage Systems in Microgrids: A Review. Energies, 2023. 16(1): p. 106.
  42. Hampton, H. and A. Foley, A review of current analytical methods, modelling tools and development frameworks applicable for future retail electricity market design. Energy, 2022: p. 124861.
  43. Jani, P., K.A. Vyas, and J. Jamnani, Deployment of standalone Software for Performance Analysis of Substation Grounding System. idea, 2014. 3: p. 8.
  44. Kalair, A., et al., Review of harmonic analysis, modeling and mitigation techniques. Renewable and Sustainable Energy Reviews, 2017. 78: p. 1152-1187.
  45. Gupta, B.B. and T. Akhtar, A survey on smart power grid: frameworks, tools, security issues, and solutions. Annals of Telecommunications, 2017. 72: p. 517-549.
  46. Sanchez-Hidalgo, M.-A. and M.-D. Cano, A survey on visual data representation for smart grids control and monitoring. Sustainable Energy, Grids and Networks, 2018. 16: p. 351-369.
  47. Shertukde, H.M., Power systems analysis illustrated with matlab and etap. 2019: CRC Press.
  48. Agarwal, U. and N. Jain, Distributed energy resources and supportive methodologies for their optimal planning under modern distribution network: a review. Technology and Economics of Smart Grids and Sustainable Energy, 2019. 4: p. 1-21.
  49. Lau, E.T., et al. A Strategic Urban Grid Planning Tool to Improve the Resilience of Smart Grid Networks. in Smart Cities, Green Technologies, and Intelligent Transport Systems: 6th International Conference, SMARTGREENS 2017, and Third International Conference, VEHITS 2017, Porto, Portugal, April 22-24, 2017, Revised Selected Papers 6. 2019. Springer.
  50. Abda, Z.M.K., et al., A review of geomagnetically induced current effects on electrical power system: Principles and theory. IEEE Access, 2020. 8: p. 200237-200258.
  51. Trahan, R.T. and D.J. Hess, Who controls electricity transitions? Digitization, decarbonization, and local power organizations. Energy Research & Social Science, 2021. 80: p. 102219.
  52. Kumar, N. and M. Tripathi, Design of a Novel Solar Energy Market Model for Indian Scenario. Journal of Electrical Engineering & Technology, 2021. 16(5): p. 2783-2792.
  53. Satpathy, R. and V. Pamuru, Chapter 9—Grid-connected solar PV power systems. Solar PV Power; Satpathy, R., Pamuru, V., Eds, 2021: p. 365-433.
  54. Rif’an, M., et al. Comparison of load flow analysis using PSAT and ETAP. in IOP Conference Series: Materials Science and Engineering. 2021. IOP Publishing.
  55. Shair, J., et al., Modeling and stability analysis methods for investigating subsynchronous control interaction in large-scale wind power systems. Renewable and Sustainable Energy Reviews, 2021. 135: p. 110420.
  56. Nocoń, A. and S. Paszek, A Comprehensive Review of Power System Stabilizers. Energies, 2023. 16(4): p. 1945.
  57. Lujano-Rojas, J., R. Dufo-López, and J.A. Domínguez-Navarro, 2 - Genetic algorithms and other heuristic techniques in power systems optimization, in Genetic Optimization Techniques for Sizing and Management of Modern Power Systems, J. Lujano-Rojas, R. Dufo-López, and J.A. Domínguez-Navarro, Editors. 2023, Elsevier. p. 41-95.
  58. Hay, S. and A. Ferguson, A review of power system modelling platforms and capabilities. IET Special Interest Publication for the Council for Science and Technology, 2015: p. 3-13.
  59. Schmeling, L., et al. Review of different Software Solutions for the holistic Simulation of distributed hybrid Energy Systems for the commercial Energy Supply. in Proceedings of the 33rd European Photovoltaic Solar Energy Conference and Exhibition, Amsterdam, The Netherlands. 2017.
  60. Sinha, S. and S.S. Chandel, Review of software tools for hybrid renewable energy systems. Renewable and sustainable energy reviews, 2014. 32: p. 192-205.
  61. Klaric, M., I. Kuzle, and T. Tomisa. Simulation of undervoltage load shedding to prevent voltage collapse. in 2005 IEEE Russia Power Tech. 2005. IEEE.
  62. Thakur, T. Minimum loss configuration of power distribution system. in 2006 International Conference on Power Electronic, Drives and Energy Systems. 2006. IEEE.
  63. Thakur, T. and J. Dhiman. A new approach to load flow solutions for radial distribution system. in 2006 IEEE/PES Transmission & Distribution Conference and Exposition: Latin America. 2006. IEEE.
  64. Ulinuha, A., M. Masoum, and S. Islam. Optimal dispatch of LTC and shunt capacitors in the presence of harmonics using genetic algorithms. in 2006 IEEE PES Power Systems Conference and Exposition. 2006. IEEE.
  65. Ulinuha, A., M. Masoum, and S. Islam. Harmonic power flow calculations for a large power system with multiple nonlinear loads using decoupled approach. in 2007 Australasian Universities Power Engineering Conference. 2007. IEEE.
  66. Alinejad-Beromi, Y., et al. Using genetic alghoritm for distributed generation allocation to reduce losses and improve voltage profile. in 2007 42nd International Universities Power Engineering Conference. 2007. IEEE.
  67. Sedighizadeh, M. and A. Rezazadeh, Using genetic algorithm for distributed generation allocation to reduce losses and improve voltage profile. World Academy of Science, Engineering and Technology, 2008. 37(1): p. 251-256.
  68. Hegazy, A. and Y. Galal. A Fuzzy Technique for Voltage Control During Parallel Operation between In-plant Generation and Utility. in 2007 IEEE Power Engineering Society Conference and Exposition in Africa-PowerAfrica. 2007. IEEE.
  69. Jabbar, R.A., et al. Impact of compact fluorescent lamp on power quality. in 2008 Australasian Universities Power Engineering Conference. 2008. IEEE.
  70. Rezaei, N. and M.-R. Haghifam, Protection scheme for a distribution system with distributed generation using neural networks. International Journal of Electrical Power & Energy Systems, 2008. 30(4): p. 235-241.
  71. Swarup, K.S., Artificial neural network using pattern recognition for security assessment and analysis. Neurocomputing, 2008. 71(4-6): p. 983-998.
  72. Ellithy, K., A. Al-Hinai, and A. Moosa, Optimal shunt capacitors allocation in distribution networks using genetic algorithm-practical case study. International journal of innovations in energy systems and power, 2008. 3(1): p. 13-45.
  73. Wang, L., et al. Stability and security assessment for an industrial electric grid with enterprise-owned power plants. in 2008 Third International Conference on Electric Utility Deregulation and Restructuring and Power Technologies. 2008. IEEE.
  74. Jian, C. Harmonic suppression of 220kV Gong Ping power station. in 2008 China International Conference on Electricity Distribution. 2008. IEEE.
  75. Sayed, A.G. and H.K. Youssef. Optimal sizing of fixed capacitor banks placed on a distorted interconnected distribution networks by genetic algorithms. in 2008 IEEE Region 8 International Conference on Computational Technologies in Electrical and Electronics Engineering. 2008. IEEE.
  76. Porate, K., K. Thakre, and G. Bodhe, Voltage stability enhancement of low voltage radial distribution network using static var compensator: a case study. WSEAS Transactions on Power Systems, 2009. 4(1): p. 32-41.
  77. Qureshi, S., M. Akmal, and R. Arif. Power quality based comparison of compact fluorescent lamp with fluorescent light. in 2009 Third International Conference on Electrical Engineering. 2009. IEEE.
  78. Jabbar, R.A., et al. Impacts of harmonics caused by Personal Computers on distribution transformers. in 2009 Third International Conference on Electrical Engineering. 2009. IEEE.
  79. Mostafa, Y.G. and M.S. Aly. Neural network based overcurrent voltage controlled protection system in large electrical networks. in 2009 IEEE Bucharest PowerTech. 2009. IEEE.
  80. Liang, X. and W.M. Jackson, Influence of subsea cables on offshore power distribution systems. IEEE Transactions on Industry Applications, 2009. 45(6): p. 2136-2144.
  81. Hairi, M.H., et al. Computer Aided Protection (Overcurrent) Coordination Studies. in 2009 Second International Conference on Computer and Electrical Engineering. 2009. IEEE.
  82. Manio, L., et al. Sequential Motor Dynamic Acceleration and Reacceleration Simulations: Comparison of ETAP® and EMTP-RV® Software. in International Conference of Power Systems Transients. 2009.
  83. Huang, W.-T. and S.-T. Chen. Sequential three-phase power flow calculation for radial distribution systems via three-phase Z-bus distribution factor. in 2009 Fourth International Conference on Innovative Computing, Information and Control (ICICIC). 2009. IEEE.
  84. El-Naggar, K.M., H.M. Ismail, and M. Al-Fahd, Harmonic modeling, analysis, mitigation of Kuwait EHV electrical network. Electrical Engineering, 2009. 91(3): p. 145-152.
  85. Khan, R.A.J., M. Junaid, and M.M. Asgher. Analyses and monitoring of 132 kV grid using ETAP software. in 2009 International Conference on Electrical and Electronics Engineering-ELECO 2009. 2009. IEEE.
  86. Sun, S., et al. Comparison with three projects of auxiliary power wiring for 1000MW unit based on ETAP. in 2009 Asia-Pacific Power and Energy Engineering Conference. 2009. IEEE.
  87. Mostafa, Y.G., M.S. Hussien, and N. ElAmary. Co-ordination of overcurrent voltage controlled protection in large electrical networks using particle swarm optimization technique. in 2009 International Conference on Computer Engineering & Systems. 2009. IEEE.
  88. Ramesh, L., et al., Minimization of power loss in distribution networks by different techniques. International Journal of Electrical and Computer Engineering, 2009. 3(4): p. 661-667.
  89. Patil, P.S. and K. Porate. Starting analysis of induction motor: A computer simulation by ETAP power station. in 2009 Second International Conference on Emerging Trends in Engineering & Technology. 2009. IEEE.
  90. Liang, X. and J. Lim, Power-system protection in an oil-field distribution system. IEEE Transactions on Industry Applications, 2009. 46(1): p. 340-348.
  91. Zheng, F., et al. Study on large asynchronous motor starting check for auxiliary power system. in 2010 Asia-Pacific Power and Energy Engineering Conference. 2010. IEEE.
  92. Tabatabaei, N. and S. Mortezaeei, Design of grounding systems in substations by ETAP intelligent software. International Journal on «Technical and Physical Problems of Engineering, 2010. 2: p. 45-49.
  93. Attia, H.A., et al., An assessment of distributed generation impacts on distribution networks using global performance index. Nat. Sci., 2010. 8: p. 150-158.
  94. Bo, Z., G. Weller, and T. Lomas, A new technique for transformer protection based on transient detection. IEEE transactions on Power Delivery, 2000. 15(3): p. 870-875.
  95. Porate, K. and S.C. Gabhane. Transient Analysis of 220kV Distribution Substation: A Case Study. in 2010 3rd International Conference on Emerging Trends in Engineering and Technology. 2010. IEEE.
  96. Shalwala, R. and J. Bleijs. Impact of Grid-Connected PV systems on voltage regulation of a residential area network in Saudi Arabia. in 2010 1st International Nuclear & Renewable Energy Conference (INREC). 2010. IEEE.
  97. Davudi, M., S. Torabzad, and B. Ojaghi, Analysis of harmonics and harmonic mitigation methods in distribution systems. Australian Journal of Basic and Applied Sciences, 2011. 5(11): p. 996-1005.
  98. Neelima, S. and P. Subramanyam, OPTIMAL CAPACITORS PLACEMENT IN DISTRIBUTION NETWORKS USING GENETIC ALGORITHM: A DIMENSION REDUCING APPROACH. Journal of Theoretical & Applied Information Technology, 2011. 30(1).
  99. Liang, X., J. Lim, and O. Ilochonwu, Power system optimization for industrial facilities using power studies. IEEE Transactions on Industry Applications, 2012. 48(3): p. 1095-1106.
  100. Tin, H., A. Abu-Siada, and M.S. Masoum. Impact of harmonics on the performance of over-current relays. in AUPEC 2011. 2011. IEEE.
  101. Ramesh, L., N. Chakraborty, and S. Chowdhury. Voltage measurement location for state estimation in embedded distribution system. in International Conference on Sustainable Energy and Intelligent Systems (SEISCON 2011). 2011. IET.
  102. Bawan, E.K. Distributed generation impact on power system case study: Losses and voltage profile. in 2012 22nd Australasian Universities Power Engineering Conference (AUPEC). 2012. IEEE.
  103. Raveendran, V. and S. Tomar, Modeling, Simulation, Analysis and Optimisation of a Power System Network-Case Study. Int. J. Sci. Eng. Res, 2012. 3(6).
  104. Rusilawati, R., Determination of generator steady state stability limit using losses concept and RBFNN. Telecomunication, Electronic And Computer Engineering, 2012. 9(2-3): p. 161-166.
  105. Jaleel, J.A. and M.F. Sadina. Reliability analysis using fault tree method and its prediction using neural networks. in 2013 International Conference on Control Communication and Computing (ICCC). 2013. IEEE.
  106. Sun, S., et al. Optimizing Design on Emergency Power Supply of Large Dynamotor Unit. in 2013 Fourth International Conference on Digital Manufacturing & Automation. 2013. IEEE.
  107. Zhu, H., X. Liu, and N.E. Mastorakis. The simulation analysis of motor startup based on the ETAP platform. in 2014 International Conference on Mathematics and Computers in Sciences and in Industry. 2014. IEEE.
  108. Shahnia, F., M. Moghbel, and H.H. Yengejeh. Improving the learning experience of power system protection students using computer-based simulations and practical experiments. in 2014 Australasian Universities Power Engineering Conference (AUPEC). 2014. IEEE.
  109. Shahnia, F., M. Moghbel, and H.H. Yengejeh, Motivating power system protection course students by practical and computer-based activities. IEEE Transactions on Education, 2015. 59(2): p. 81-90.
  110. Aslam, M.U., et al. Design analysis and optimization of ground grid mesh of extra high voltage substation using an intelligent software. in 2014 The 1st International Conference on Information Technology, Computer, and Electrical Engineering. 2014. IEEE.
  111. Khoshkbar-Sadigh, A., et al. A unified platform enabling power system circuit model data transfer among different software. in 2015 IEEE Power & Energy Society Innovative Smart Grid Technologies Conference (ISGT). 2015. IEEE.
  112. Goswami, U., P.K. Sadhu, and S. Chakraborty, Enhancement of controllability to improve the transient performance for captive power plant in islanding condition: A case of study. International Journal of Electrical Power & Energy Systems, 2016. 83: p. 188-202.
  113. Sagar, N., G. Pavan, and M. Rajalakshmi, Transient Stability Analysis of IEEE 59 Bus System with FCL and SVC Controller Using ETAP. Journal of Chemical and Pharmaceutical Sciences, 2016: p. 248-251.
  114. Shwehdi, M., et al. Harmonic flow study and evaluation of a petrochemical plant in Saudi Arabia. in LESCOPE'02. 2002 Large Engineering Systems Conference on Power Engineering. Conference Proceedings. 2002. IEEE.
  115. Shukla, M. and A. Sekar. Steady security assessment using linear programming methodology. in Thirty-Sixth Southeastern Symposium on System Theory, 2004. Proceedings of the. 2004. IEEE.
  116. Eseosa, O. and E.A. Ogujor, Determination of bus voltages, power losses and flows in the Nigeria 330kV integrated power system. International Journal of Advances in Engineering & Technology, 2012. 4(1): p. 94.
  117. Eseosa, O. and F.O. Odiase, efficiency improvement of nigeria 330kv network using flexible alternating current transmission system (facts) devices. International Journal of Advances in Engineering & Technology, 2012. 4(1): p. 26.
  118. Vyas, K.A. and J. Jamnani. MATLAB GUI Development Environment Simplifies Deployment of Standalone Software for Optimal Design of Substation Grounding Systems. in International Conference on Computer Science and Information Technology–ICCSIT. 2012.
  119. Vyas, K.A. and J. Jamnani, Development of IEEE complaint software'economical substation grounding system designer'using matlab gui development environment. International Journal on Electrical Engineering and Informatics, 2012. 4(2): p. 335.
  120. Vyas, K.A. and J. Jamnani, Optimal design of grounding system for HV/EHV substations in two layered soil. International Journal of Emerging Technology and Advanced Engineering, 2012. 2(5): p. 383-392.
  121. Al-Shaher, M., A.S. Saleh, and M.M. Sabry, Estimation of fault location and fault resistance for single line-to-ground faults in multi-ring distribution network using artificial neural network. Electric Power Components and Systems, 2009. 37(7): p. 697-713.
  122. Ramesh, L., et al. Voltage stability analysis and real power loss reduction in distributed distribution system. in 2008 IEEE/PES Transmission and Distribution Conference and Exposition. 2008. IEEE.
  123. Ramesh, L., N. Chakraborty, and S. Chowdhury, Intelligent algorithm for optimal meter placement and bus voltage estimation in ring main distribution system. Frontiers in Energy, 2012. 6(1): p. 47-56.
  124. Hairi, M., et al., An Investigation of Short Circuit Analysis in Komag Sarawak Operations (KSO) Factory. World Academy of Science, Engineering and Technology, International Journal of Electrical, Computer, Energetic, Electronic and Communication Engineering, 2009. 3(11): p. 1940-1945.
  125. Kamel, A., et al., Protection coordination for distribution systems in presence of distributed generators. Electric power Components and systems, 2013. 41(15): p. 1555-1566.
  126. Sarkar, P., S. Chatterjee, and S. Ray, Optimal placement of capacitor for voltage support and minimizing overall cost in radial distribution system. International Journal of Computer Applications, 2013. 65(2).
  127. Gulo, F., S. Syafriyudin, and M. Mujiman, MODELING OF THE TURN OF HIGH VOLTAGE OVERHEAD POWER TRANSMISSION LINES WITH UNDERGROUND CABLE ON FOUR BUSES OF TRANSMISSION LINES FOR IMPROVEMENT THE VOLTAGE PROFILE ON THE SYSTEM (Case Study: Transmission Line 150 kV Region III Sub-system Yogyakarta). Jurnal Elektrikal, 2014. 1(1): p. 37-46.
  128. Chatterjee, S., et al., Advantage of DG for improving voltage profile over facts devices. Int. J. Eng. Res. Appl, 2013. 3: p. 2029-2032.
  129. Folorunso, O., C. Osuji, and O. Ighodalo, Enhancement of power system voltage stability with the aid of reactive/capacitive power switching mechanism:(a case study of Owerri Transmission Company of Nigeria). Journal of Advancement in Engineering and Technology, 2014. 2(1): p. 1-6.
  130. Tran, V.-T. and T.-H. Chen, Wind energy resources on Phuquoc island, Vietnam. Energy Sources, Part A: Recovery, Utilization, and Environmental Effects, 2016. 38(11): p. 1612-1619.
  131. Chopade, P. and M. Bikdash. Minimizing cost and power loss by optimal placement of capacitor using ETAP. in 2011 IEEE 43rd Southeastern Symposium on System Theory. 2011. IEEE.
  132. Tran, V.-T., T.-H. Chen, and T.-Y. Hsieh. Simulation offshore wind farm in Penghu Island, Taiwan. in 2012 10th International Power & Energy Conference (IPEC). 2012. IEEE.
  133. Scholar, P., AdvantageOf DG To Mitigate Voltage Collapse over Facts Devices.
  134. Farahmand, F., et al. An enterprise approach to the interactive objectives and constraints of smart grids. in 2011 IEEE PES Conference on Innovative Smart Grid Technologies-Middle East. 2011. IEEE.
  135. Sonwane, P.M. and B. Kushare. Optimal Capacitor Configuration for Enhancement of System Reliability using Genetic Algorithm: A case study of IEEE 30 Bus system. in Fourth International Joint Journal Conferences in Engineering. 2012.
  136. Olatoke, A. and M.K. Darwish. A study of the impact of Distributed Generation on power quality. in 2012 47th International Universities Power Engineering Conference (UPEC). 2012. IEEE.
  137. Goswami, U., T.K. Sengupta, and A. Das, Improvement of transient stability performance of captive power plant during islanding condition. TELKOMNIKA Indonesian Journal of Electrical Engineering, 2014. 12(12): p. 8001-8007.
  138. Thiraporn, W. and S. Vongkulluk. Case study: arc flash study of wang noi combined cycle power plant by handy arc flash calculator. in 2019 IEEE PES GTD Grand International Conference and Exposition Asia (GTD Asia). 2019. IEEE.
  139. Smith, N. and R. McCann. Analysis of distributed generation sources and load shedding schemes on isolated grids case study: The Bahamas. in 2014 International Conference on Renewable Energy Research and Application (ICRERA). 2014. IEEE.
  140. Ayodele, T., A. Ogunjuyigbe, and O. Oyewole, Comparative assessment of the effect of earthing grid configurations on the earthing system using IEEE and Finite Element Methods. Engineering science and technology, an international journal, 2018. 21(5): p. 970-983.
  141. Sauhats, A., et al., Enhancing power system frequency with a novel load shedding method including monitoring of synchronous condensers’ power injections. Energies, 2021. 14(5): p. 1490.
  142. Husnayain, F., et al. Harmonics mitigation for offshore platform using active filter and line reactor methods. in 2014 International Conference on Electrical Engineering and Computer Science (ICEECS). 2014. IEEE.
  143. Ceaki, O., et al. Analysis of electromagnetic disturbances with or without SVC device. in 2015 50th International Universities Power Engineering Conference (UPEC). 2015. IEEE.
  144. Amadi, H., F. Izuegbunam, and E. Okafor, Evaluation of Losses in Distribution Networks of Selected Industrial Cities in Nigeria Using ETAP. British Journal of Applied Science & Technology, 2016. 17(6): p. 1-12.
  145. Kumolo, C., Analisis Aliran Beban pada Sistem Tenaga Listrik di KSO Pertamina EP–GEO Cepu Indonesia Distrik 1 Kawengan menggunakan Software ETAP 12.6. Emitor: Jurnal Teknik Elektro, 2016. 16(1): p. 1-15.
  146. Mohsin, Q.K., et al. Optimal placement and capacity of capacitor bank in radial distribution system. in 2016 International Conference on Energy Efficient Technologies for Sustainability (ICEETS). 2016. IEEE.
  147. Ceaki, O., et al. Analysis of power quality improvement in smart grids. in 2017 10th international symposium on advanced topics in electrical engineering (ATEE). 2017. IEEE.
  148. Idoniboyeobu, D., T. Bala, and K. Blue-Jack, Performance Evaluation of the 132KV Sub-Transmission Lines in the Nigeria Power Network: A Case Study of Port Harcourt Sub-Region, Rivers State. International Journal of Research in Engineering and Science, 2017. 5(12): p. 28-40.
  149. Omran, A.S., N.H. Abbasy, and R.A. Hamdy, Enhanced performance of substation dynamics during large induction motor starting using SVC. Alexandria engineering journal, 2018. 57(4): p. 4059-4070.
  150. Idoniboyeobu, D., S. Braide, and O. Igbogidi, Improved Relay Coordination In Port Harcourt Distribution Network Case Study Of RSU 2 X 15MVA, 33/11kv Injection Substation. simulation, 2018. 15: p. 16.
  151. Ghiasi, M., A detailed study for load flow analysis in distributed power system. International Journal of Industrial Electronics Control and Optimization, 2018. 1(2): p. 153-160.
  152. Soe, K.T., T.M. Aye, and A.A. Mon, Design of Earthing System for 230 kV High Voltage Substation by ETAP 12.6 Software. 2019.
  153. Nassar, S.R., et al., Evaluating the Impact of Connected Non Linear Loads on Power Quality-a Nuclear Reactor case study. Journal of Radiation Research and Applied Sciences, 2020. 13(1): p. 688-697.
  154. Ahiakwo, C., S. Braide, and O. Azubuike, Optimization of Egi-Clan 33KV Power Distribution System for Improved Performance. Global Scientific Journals, 2020. 8(11).
  155. ETTA, B.-O. and D. IDONIBOYEOBU, Improved Performance of Elelenwo 11kv Electric Power Distribution Network Using Newton Raphson Load Flow. 2021.
  156. NLERUM, S., S. BRAIDE, and H. AMADI, Transient Stability Assessment of Nigerian 330kv Power Grid Using Modified Euler Technique. 2021.
  157. Kurniawan, R., et al., The effect of distributed generator injection with different numbers of units on power quality in the Electric Power System. Journal of Renewable Energy, Electrical, and Computer Engineering, 2021. 1(2): p. 71-78.
  158. UKWUEZE, S.C., D. Idoniboyeobu, and S. Braide, Improved Lightning Protection for Low Voltage Power System using Equipotential Bonding Technique.
  159. Abd el-Ghany, H.A., S.H. Abd-El Fattah, and A.M. Azmy, Evaluating the effect of considering repairing-fault periods on calculating technical losses in medium-voltage feeders of ring distribution networks. Electric Power Systems Research, 2021. 196: p. 107192.
  160. Abbas, A., R.D. Kamal, and S.A.A. Elmustafa, Power system transient stability case study: a power sub-station plant in Sudan. World Scientific News, 2021. 158: p. 267-284.
  161. Yenigha, L.S., et al., Improved Randomized Flow Model for 330kV Electric Power Transmission Network. European Journal of Advances in Engineering and Technology, 2022. 9(11): p. 1-11.
  162. Daud, M., et al., Economic Calculations of Electricity Using AC System on Residential Load. Andalasian International Journal of Applied Science, Engineering and Technology, 2022. 2(3): p. 140-148.
  163. Joung, S. and B.H. Kim, Comparative analysis and countermeasures of power system open phase conditions in Korea’s standard nuclear power plants. Nuclear Engineering and Design, 2022. 393: p. 111806.
  164. Karmiathi, N.M. and I.K. Adiana Putra, Technical analysis of power factor improvement using ETAP 12.6 at Regent Resort & Holiday Inn Canggu. Matrix : Jurnal Manajemen Teknologi dan Informatika, 2022. 12(1): p. 38-50.
  165. Maizana, D., et al., Stability analysis of smart grid management system on campus building. Indonesian Journal of Electrical Engineering and Computer Science, 2023. 30(3): p. 1321-1330.
  166. Fatma, S., et al., The Protection Relay Coordination Studies (Over Current Relays and Ground Fault Relays) On The Power Plant Electrical System, PT. Rekind Daya Mamuju By Using The ETAP 12.6 Program. JEEE-U (Journal of Electrical and Electronic Engineering-UMSIDA), 2023. 7(1): p. 94-106.
  167. Elkadeem, M., M. Alaam, and A.M. Azmy, Improving performance of underground MV distribution networks using distribution automation system: A case study. Ain Shams Engineering Journal, 2018. 9(4): p. 469-481.
  168. Aristizábal Cardona, A.J., et al., Behavior and Analysis of the Power System in Steady State. Building-Integrated Photovoltaic Systems (BIPVS) Performance and Modeling Under Outdoor Conditions, 2018: p. 109-118.
  169. Abrha, E.B., G.B. Worku, and T.A. Abose. Power Distribution System Reliability Assessment and Improvement Case of Jimma Town, Ethiopia. in Advances of Science and Technology: 7th EAI International Conference, ICAST 2019, Bahir Dar, Ethiopia, August 2–4, 2019, Proceedings 7. 2020. Springer.
  170. Dib, M., M. Ramzi, and A. Nejmi, Voltage regulation in the medium voltage distribution grid in the presence of renewable energy sources. Materials Today: Proceedings, 2019. 13: p. 739-745.
  171. Chen, X. and G. Zhang. Harmonic analysis of AC-DC hybrid microgrid based on ETAP. in 2016 IEEE 8th International Power Electronics and Motion Control Conference (IPEMC-ECCE Asia). 2016. IEEE.
  172. Sinishaw, G.Y., B. Bantyirga, and K. Abebe, Analysis of smart grid technology application for power distribution system reliability enhancement: A case study on Bahir Dar power distribution. Scientific African, 2021. 12: p. e00840.
  173. Al-bayaty, H., et al., Electrical distribution grid of Kirkuk City: A case study of load flow and short circuit valuation using ETAP. Periodicals of Engineering and Natural Sciences, 2022. 10(3): p. 311-322.
  174. Magro, M.C., et al., Real time simulator for microgrids. Electric Power Systems Research, 2018. 160: p. 381-396.
  175. Chary, P.K., et al. Load flow analysis of radial distribution system. in 2020 International Conference on Smart Technologies in Computing, Electrical and Electronics (ICSTCEE). 2020. IEEE.
  176. Eduardo, E.G.-L., R.F.-M. Rafael, and L.B.M.-S.L. Bernardo, Use of the frequency response technique to analyze the impact of improving the power factor in the electrical networks. IEEE Latin America Transactions, 2019. 17(06): p. 914-920.
  177. Shin, H., S.H. Chae, and E.-H. Kim, Design of microgrid protection schemes using PSCAD/EMTDC and ETAP programs. Energies, 2020. 13(21): p. 5784.
  178. Salih, T.K.M., Z.S. Hussain, and F.S. Ahmed, Voltage Profile Enhancing Using HVDC for 132KV Power System: Kurdistan Case Study. Journal of Engineering, 2022. 28(1): p. 52-64.
  179. Takele, H., Distributed generation adverse impact on the distribution networks protection and its mitigation. Heliyon, 2022. 8(6).
  180. Khatua, S. and V. Mukherjee, Application of integrated microgrid for strengthening the station blackout power supply in nuclear power plant. Progress in Nuclear Energy, 2020. 118: p. 103132.
  181. Bugaliya, A.K., G. Vardhan, and O. Rahi. Design and Analysis of Grounding Grid Performance Using ETAP 16.0. 0 Software. in Renewable Power for Sustainable Growth: Proceedings of International Conference on Renewal Power (ICRP 2020). 2021. Springer.
  182. Hossain, M.S., R. Ahmed, and S. Hossain, Design and optimization of substation grounding grid for ensuring the safety of personnel and equipment. Journal of Electrical Power & Energy Systems, 2021. 5(1): p. 71-80.
  183. Muhammad, R.D., S. Makmur, and S.Y. AM, Load Flow Analysis After the Entry of Renewable Power Plants in the Sulselrabar System. Journal of Electrical Technology UMY (JET-UMY), 2021. 5(2): p. 80-87.
  184. Barie, E.Z. and C.-k. Chang, Application of variable frequency drive on the condensate pump motors of APR1400 nuclear power plants for energy savings. Journal of International Council on Electrical Engineering, 2018. 8(1): p. 179-189.
  185. Ikonwa, W., et al., Power Flow Studies of 132/33/11 kV Distribution Network Using Static Var Compensator for Voltage Improvement. American Journal of Engineering Research. 12(3).
  186. Ibrahim, L.O., et al., A Feasibility Study of Frequency Regulation Energy Storage System Installation in a Power Plant. Energies, 2020. 13(20): p. 5365.
  187. Fawwas, J.F., S. Abduh, and T.K. Sari, Analisis Penyeimbangan Beban Transformator Distribusi 400kva 20kv/400v Menggunakan Software ETAP 19.0. 1. Jetri: Jurnal Ilmiah Teknik Elektro, 2022: p. 223-236.
  188. Salam, I.U., et al., Optimizing Distributed Generation Placement and Sizing in Distribution Systems: A Multi-Objective Analysis of Power Losses, Reliability, and Operational Constraints. Energies, 2023. 16(16): p. 5907.
  189. Weimann, C.S., R.J. Kerestes, and B.M. Grainger, Comparative analysis of experimental DC arc flash results to industry estimation methods. IEEE Open Journal of Industry Applications, 2020. 1: p. 181-193.
  190. Monakov, Y., et al., Optimization of Equipment Operation in Power Systems Based on the Use in the Design of Frequency-Dependent Models. Energies, 2023. 16(18): p. 6756.
  191. Tan, Z.H., et al., Optimal operations of transformers in railway systems with different transformer operation modes and different headway intervals. International Journal of Electrical Power & Energy Systems, 2021. 127: p. 106631.
  192. Mohajeryami, S., M. Arefi, and Z. Salami. Arc flash analysis: Investigation, simulation and sensitive parameter exploration. in 2017 North American Power Symposium (NAPS). 2017. IEEE.
  193. Yusupbekov, N., et al., Intelligent automation of power transmission and distribution systems for industrial enterprises.
  194. Luna, E.G., R.F. Manrique, and E.L.P. Bocanegra. Monitoring and Control System Using ETAP Real-Time on Generation Plant Emulation Using OPAL-RT. in 2018 IEEE ANDESCON. 2018. IEEE.
  195. Shakoor, R., et al., Performance analysis of biogas net metering with the grid-connected station. International Journal of Ambient Energy, 2023. 44(1): p. 811-821.
  196. Tahir, M.U., et al., Evaluation of single-phase net metering to meet renewable energy targets: A case study from Pakistan. Energy Policy, 2023. 172: p. 113311.
  197. Gamboa, R.A., C. Aravind, and C.A. Chin. Power system network contingency studies. in 2018 IEEE Student Conference on Research and Development (SCOReD). 2018. IEEE.
  198. Irfan, W., et al. N-1 Contingency Analysis for Offsite Power System of an HPR-1000 Power Plant Using ETAP Software. in 2022 International Conference on Recent Advances in Electrical Engineering & Computer Sciences (RAEE & CS). 2022. IEEE.
  199. Kumar, A. and T. Ghose, An algorithm for contingency analysis of the AC-DC networks using modified Z-bus technique. Electric Power Systems Research, 2022. 210: p. 108138.
  200. Shariatinasab, R. and M. Akbari. New islanding detection technique for DG using discrete wavelet transform. in 2010 IEEE International Conference on Power and Energy. 2010. IEEE.
  201. Attia, H.A., et al. An assessment of a global performance index for distributed generation impacts on distribution systems. in Proceedings of the 14th International Middle East Power Systems Conference (MEPCON'10). 2010.
  202. Sivakumar, P. and C. Birindha. Stability enhancement of DG sourced power system with modified AVR and PSS. in 2013 International Conference on Computation of Power, Energy, Information and Communication (ICCPEIC). 2013. IEEE.
  203. Prakash, P., V.A. Verma, and R. Jha, Distribution System Reliability Analysis Using ETAP. 2014, isrjournal.
  204. Elhaffar, A., N. El-Naily, and K. El-Arroudi, Management of distribution system protection with high penetration of DGs, in Energy Systems and Management. 2015, Springer. p. 279-291.
  205. Khan, Z.W. and S. Khan. Analyzing the impacts of Distributed Generation on power losses and voltage profile. in 2015 International Conference on Emerging Technologies (ICET). 2015. IEEE.
  206. Duong, M.Q., et al. The impacts of distributed generation penetration into the power system. in 2017 International Conference on Electromechanical and Power Systems (SIELMEN). 2017. IEEE.
  207. Saad, S.M., et al. An optimized proactive over-current protection scheme for modern distribution grids integrated with distributed generation units. in 2018 9th International Renewable Energy Congress (IREC). 2018. IEEE.
  208. Musirikare, A., et al. ANN-Based modeling of directional overcurrent relay characteristics applied in radial distribution system with distributed generations. in 2018 10th International Conference on Information Technology and Electrical Engineering (ICITEE). 2018. IEEE.
  209. Wafi, J., et al. Applicability analysis of proactive recloser-fuse scheme for wind distributed generation into modern distribution network. in 2018 9th International Renewable Energy Congress (IREC). 2018. IEEE.
  210. Chandraratne, C., et al. Adaptive overcurrent protection for power systems with distributed generators. in 2018 8th International Conference on Power and Energy Systems (ICPES). 2018. IEEE.
  211. Kamaruzaman, M.Z., N.I.A. Wahab, and M.N.M. Nasir. Reliability assessment of power system with renewable source using ETAP. in 2018 International Conference on System Modeling & Advancement in Research Trends (SMART). 2018. IEEE.
  212. Kadukar, P.R., P.S. Shete, and S. Gawande. Transient analysis of distributed generation ac microgrid using ETAP. in 2018 International Conference on Current Trends towards Converging Technologies (ICCTCT). 2018. IEEE.
  213. Abbaspour, E., B. Fani, and E. Heydarian-Forushani, A bi-level multi agent based protection scheme for distribution networks with distributed generation. International Journal of Electrical Power & Energy Systems, 2019. 112: p. 209-220.
  214. Sridevi, J., V.U. Rani, and B.L. Rao. Integration of renewable DGs to radial distribution system for loss reduction and voltage profile improvement. in 2019 1st International Conference on Electrical, Control and Instrumentation Engineering (ICECIE). 2019. IEEE.
  215. Rizwan, M., et al., Sustainable protection coordination in presence of distributed generation with distributed network. International Transactions on Electrical Energy Systems, 2020. 30(3): p. e12217.
  216. Alghassab, M. Adaptive Protection of Distribution Networks Integrated With DG Units. in 2019 2nd International Conference on Computer Applications & Information Security (ICCAIS). 2019. IEEE.
  217. Farkhani, J.S., et al. Coordination of directional overcurrent protection relay for distribution network with embedded DG. in 2019 5th Conference on Knowledge Based Engineering and Innovation (KBEI). 2019. IEEE.
  218. Subramanian, S., J. Keerthana, and V. Murali. Analysis on fault current contribution by different types of DGs and relay coordination in non-autonomous micro-grids. in 2019 National Power Electronics Conference (NPEC). 2019. IEEE.
  219. Sharma, P., et al., EFFECT ON PROTECTION SCHEME BY DG IN ETAP.
  220. Fayazi, H., et al., An offline three-level protection coordination scheme for distribution systems considering transient stability of synchronous distributed generation. International Journal of Electrical Power & Energy Systems, 2021. 131: p. 107069.
  221. Kiani, A., B. Fani, and G. Shahgholian, A multi-agent solution to multi-thread protection of DG-dominated distribution networks. International Journal of Electrical Power & Energy Systems, 2021. 130: p. 106921.
  222. El-Hamrawy, A.H., A.A.M. Ebrahiem, and A.I. Megahed, Improved adaptive protection scheme based combined centralized/decentralized communications for power systems equipped with distributed generation. IEEE Access, 2022. 10: p. 97061-97074.
  223. Abbaspour, E., et al., A multi-agent based protection in distribution networks including distributed generations. Energy Reports, 2022. 8: p. 163-174.
  224. Center, N.B. and O. Informatics, Protection Methodoly for Supporting Distributed Generations with Respect to Transient Instability. 2023.
  225. El Naily, N., et al., Minimizing the impact of distributed generation of a weak distribution network with an artificial intelligence technique. Applied Solar Energy, 2017. 53: p. 109-122.
  226. Gana, M., U. Aliyu, and G. Bakare, Evaluation of the reliability of distribution system with distributed generation using ETAP. ABUAD Journal of Engineering Research and Development, 2019. 2(1): p. 103-110.
  227. Raju, K. and G. Srinivas, Reliability Evaluation Of Distribution System With Distributed Generation Using ETAP. Think India Journal, 2019. 22(14): p. 15048-15058.
  228. Jaleel, A.M. and M.K. Abd, Reliability Evaluation of Electric Distribution Network with Distributed Generation Integrated. International Journal of Intelligent Engineering & Systems, 2021. 14(5).
  229. Jaleel, A.M. and M.K. Abd, Reliability Assessment Based on Optimal DGs Planning in the Distribution Systems. Engineering and Technology Journal, 2023. 41(02): p. 280-293.
  230. Abed, M.J. and A. Mhalla, Reliability assessment of grid-connected multi-inverter for renewable power generation sector. Arab Gulf Journal of Scientific Research, 2023.
  231. Mahmoud, K.A.A., A.A.M.A. Ibrahim, and H.B.E.D.M. El. Technical Impact of PV Distributed Generation on Arc Flash Hazard in Egypt Low Voltage Distribution Networks. in 2019 International Conference on Electrical and Computing Technologies and Applications (ICECTA). 2019. IEEE.
  232. Hussain, I., et al., Power loss reduction via distributed generation system injected in a radial feeder. Mehran University Research Journal Of Engineering & Technology, 2021. 40(1): p. 160-168.
  233. Rahman, Y.A., et al. Evaluating the effect placement capacitor and distributed photovoltaic generation for power system losses minimization in radial distribution system. in AIP Conference Proceedings. 2018. AIP Publishing.
  234. Ali, H.Q., et al. Assessment of Pakistan's Power Distribution System Under Non-Conventional Distribution Generation. in 2019 IEEE 6th International Conference on Engineering Technologies and Applied Sciences (ICETAS). 2019. IEEE.
  235. Salman, M., et al., Enhancing Voltage Profile and Power Loss Reduction Considering Distributed Generation (DG) Resources. Engineering, Technology & Applied Science Research, 2022. 12(4): p. 8864-8871.
  236. Varghese, J.P., K. Sundaramoorthy, and A. Sankaran, Development and Validation of a Load Flow Based Scheme for Optimum Placing and Quantifying of Distributed Generation for Alleviation of Congestion in Interconnected Power Systems. Energies, 2023. 16(6): p. 2536.
  237. Jain, P., et al. Statistical Analysis of Integration of renewable DGs in IEEE-9 Bus System using ETAP Simulation. in 2023 IEEE Devices for Integrated Circuit (DevIC). 2023.
  238. Yadav, S.K., et al. Optimal coordination of overcurrent relays in power systems for reliability assessment under the presence of distributed generation using ETAP. in 2017 6th International Conference on Computer Applications In Electrical Engineering-Recent Advances (CERA). 2017. IEEE.
  239. Viet, D.T.K., K. Agbossou, and M.L. Doumbia. Voltage unbalance treatment for distribution network with massively connected distributed generators. in 2010 IEEE International Conference on Industrial Technology. 2010. IEEE.
  240. Chen, H., et al., Integrated planning of distribution systems with distributed generation and demand side response. Energy Procedia, 2015. 75: p. 981-986.
  241. George, S.P. and S. Ashok. Multiagent based adaptive relaying for distribution network with distributed generation. in 2015 International Conference on Energy, Power and Environment: Towards Sustainable Growth (ICEPE). 2015. IEEE.
  242. Eseosa, O. and E. Promise, Impact of Distributed Generation Placement on Stability of Power Network in Nigeria. IOSR Journal of Electrical and Electronics Engineering (IOSR-JEEE), 2015. 10(1): p. 61-69.
  243. Kovalenko, S., et al. New methods and approaches for monitoring and control of complex electrical power systems stability. in 2016 IEEE 16th International Conference on Environment and Electrical Engineering (EEEIC). 2016. IEEE.
  244. Ghosh, N., S. Sharma, and S. Bhattacharjee, A load flow based approach for optimum allocation of distributed generation units in the distribution network for voltage improvement and loss minimization. International Journal of Computer Applications, 2012. 50(15).
  245. Rath, A., S.R. Ghatak, and P. Goyal. Optimal allocation of Distributed Generation (DGs) and static VAR compensator (SVC) in a power system using Revamp Voltage Stability Indicator. in 2016 National Power Systems Conference (NPSC). 2016. IEEE.
  246. Varghese, J.P., S. Ashok, and S. Kumaravel. Optimal siting and sizing of DGs for congestion relief in transmission lines. in 2017 IEEE PES Asia-Pacific Power and Energy Engineering Conference (APPEEC). 2017. IEEE.
  247. Ahmad, S., et al., Impact of distributed generation on the reliability of local distribution system. International Journal of Advanced Computer Science and Applications, 2017. 8(6): p. 375-382.
  248. Sivasankaran, M.S., et al. Optimal placement and sizing of distributed generators to ensure protection coordination. in 2017 14th IEEE India Council International Conference (INDICON). 2017. IEEE.
  249. Khan, S., et al., Optimal placement of distributed generation in power system for power system loss reduction using ETAP. International Journal of Engineering and Technologies, 2019. 16: p. 7-19.
  250. Alghamdi, H., Optimum placement of distribution generation units in power system with fault current limiters using improved coyote optimization algorithm. Entropy, 2021. 23(6): p. 655.
  251. Melaku, E.D., et al., Distribution network forecasting and expansion planning with optimal location and sizing of solar photovoltaic-based distributed generation. Computers and Electrical Engineering, 2023. 110: p. 108862.
  252. Sailaja, C.V. and P. Prasad. Determination of optimal distributed generation size for losses, protection co-ordination and reliability Evaluation Using ETAP. in 2016 Biennial International Conference on Power and Energy Systems: Towards Sustainable Energy (PESTSE). 2016. IEEE.
  253. Pacis, M.C., A.M.I. Bernardo, and S.A.D. Chu. Phasor Measurement Unit (PMU) based Power System State Estimation with Distributed Generation (DG) using Integrated Alternating Current (AC) Load Flow with Weighted Least Square Algorithm. in 2021 IEEE 13th International Conference on Humanoid, Nanotechnology, Information Technology, Communication and Control, Environment, and Management (HNICEM). 2021. IEEE.
  254. Hariadi, T.K., et al., Community-Based Solar Photovoltaic Distributed Generation and its Effect on Distribution. International Energy Journal, 2023. 23(1).
  255. Dladla, V.M.N., A.F. Nnachi, and R.P. Tshubwana, Design, Modeling, and Analysis of IEEE Std 80 Earth Grid Design Refinement Methods Using ETAP. Applied Sciences, 2023. 13(13): p. 7491.
  256. Reddy, B.K., K.S. Ayyagari, and R.R. Medam, Electrical safety for residential and rural microgrids, in Residential Microgrids and Rural Electrifications. 2022, Elsevier. p. 293-320.
  257. Bashir, A., et al. ETAP software based transient, ground grid and short circuit analyses of 132 kV grid. in AIP Conference Proceedings. 2010. American Institute of Physics.
  258. Uma, U., L. Uzoechi, and B. Robert, Optimization design of ground grid mesh of 132/33kv substation using Etap. Nigerian Journal Of Technology, 2016. 35(4): p. 926-934.
  259. Singh, S. and J.G. Jamnani. Optimized Design and Analysis of Grounding Grid for 400 kV EHV Air Insulated Substation. in 2021 2nd International Conference for Emerging Technology (INCET). 2021. IEEE.
  260. Talebzadeh, M., A. Setayeshmehr, and H. Barati, Investigation of ground impedance measurement techniques up to 1 MHz frequency in urban dense power substations. Electrical Engineering, 2022. 104(6): p. 4595-4604.
  261. Jain, N.K.K., et al., Residential House Electrical Energy Audit Case Study with ETAP. Springer Artificial Intelligence and Evolutionary Computations in Engineering Systems, 2016. 394: p. 1181-1194.
  262. Kumar, A., et al., Electrical energy audit in residential house. Procedia Technology, 2015. 21: p. 625-630.
  263. Bagwan, S.U., et al. Audit and Analysis of Energy Utilization in Engineering Institution Buildings in Maharashtra. in 2020 5th International Conference on Communication and Electronics Systems (ICCES). 2020. IEEE.
  264. Keerthi Jain, K., et al. Lighting electrical energy audit and management in a commercial building. in Proceedings of 2nd International Conference on Intelligent Computing and Applications: ICICA 2015. 2016. Springer.
  265. Arya, A., et al. Energy usage analysis of industries with ETAP case study. in 2017 International Conference on Circuit, Power and Computing Technologies (ICCPCT). 2017. IEEE.
  266. Acharya, S., et al., Analysis of energy consumption, emission and saving opportunities in an educational institute in northeast India. International Journal of Energy and Water Resources, 2020. 4: p. 375-388.
  267. Devi, A., et al. Energy Conservation Implementation at Cable Manufacturing Industry through ETAP Analysis. in 2021 Emerging Trends in Industry 4.0 (ETI 4.0). 2021. IEEE.
  268. Siraj, K. and H.A. Khan, DC distribution for residential power networks—A framework to analyze the impact of voltage levels on energy efficiency. Energy Reports, 2020. 6: p. 944-951.
  269. Rajora, M., et al., Performance Simulation of Very Long Transmission Line with SVC at Mid Point.
  270. Vahabzadeh, A., H. Vadizadeh, and F. Kadkhoda. Use of unified power quality conditioner in khoozestan-iran steel complex network, a case study. in INTELEC 2009-31st International Telecommunications Energy Conference. 2009. IEEE.
  271. Katira, M. and K. Porate. Load flow analysis of 132/11 kV distribution sub station using static var compensator for voltage enhancement—A case study. in TENCON 2009-2009 IEEE Region 10 Conference. 2009. IEEE.
  272. Abhilash, V. and K. Pandey, Power Devices Implementation and Analysis in ETAP. International Journal of Engineering and Technical Research, 2014. 2: p. 273-277.
  273. SOULI, A., et al., Impact of Loads on Power Flow in Power Systems Using PowerApps and ETAP. Przegląd Elektrotechniczny, 2015. 91(7): p. 120-123.
  274. Siddique, A., et al. Load flow analysis of 132/11 kV grid station Bahawalpur region Pakistan and its voltage improvement through FACTS devices using ETAP. in 2019 IEEE Innovative Smart Grid Technologies-Asia (ISGT Asia). 2019. IEEE.
  275. Boshara, M.M., et al. The Effect of Improving the Voltage Level on the Power factor at Faroug110 kV Substation. in 2020 International Conference on Computer, Control, Electrical, and Electronics Engineering (ICCCEEE). 2021. IEEE.
  276. Nithya, S. and M. Moses, Geographical Information System (GIS) based Energy Station Identification and Frequency Analysis Using ETAP: A Sample Real Time Test Case System in INDIA. International Journal of Applied Engineering and Technology, 2021. 3(1): p. 1-6.
  277. Techane, L.B., et al., Geographical information system based optimal path routing of distribution networks. Heliyon, 2022. 8(5).
  278. Tomasović, A., M. Lasić, and B. Filipović-Grčić. Measurement and calculation of harmonics in distribution power system with connected small co-generation facility Etan. in International Conference on Renewable Energies and Power Quality (ICREPQ’09), Valencia (Spain) 15th to 17th April. 2009.
  279. Attia, H.A., M. El-Metwally, and O.M. Fahmy, Harmonic distortion effects and mitigation in distribution systems. Journal of American Science, 2010. 6(10): p. 173-183.
  280. Surasmi, N. and M. Sindhu, Optimum allocation of active filters in a 4-bus system using genetic algorithm. International Journal of Emerging Technology and Advanced Engineering, 2012. 2(4).
  281. Arif, M.R., et al. Application of passive filters to mitigate power quality problems caused by induction furnaces. in 2012 IEEE International Conference on Condition Monitoring and Diagnosis. 2012. IEEE.
  282. Barbulescu, C., et al. Electric power quality issues: Harmonic analysis for real network. in Eurocon 2013. 2013. IEEE.
  283. Corso, A., et al. Analysis of the impact of AFE active front end on the THD on a shipboard power system: A comparison study using different simulation approaches. in 2016 International Conference on Electrical Systems for Aircraft, Railway, Ship Propulsion and Road Vehicles & International Transportation Electrification Conference (ESARS-ITEC). 2016. IEEE.
  284. Nwohu, M.N., et al., Harmonic load modeling: a case study of 33 kV Abuja Steel Mill Feeder. Nigerian Journal of Technology, 2017. 36(4): p. 1184-1190.
  285. Min, G., J. Qingren, and C. Weidong. Analysis of the harmonics influence of urban rail transport load on nanning power grid based on ETAP. in 2018 13th IEEE Conference on Industrial Electronics and Applications (ICIEA). 2018. IEEE.
  286. Oun, A., I. Benabdallah, and C. Adnene, Analysis and design of a grid connected real plant in Libya using ETAP software. IJCSNS, 2018. 18(3): p. 31-40.
  287. Agrawal, A. and D.K. Singh. Harmonic impact of grid connected photovoltaic system on low voltage power system. in 2018 3rd International Conference for Convergence in Technology (I2CT). 2018. IEEE.
  288. Ayamolowo, O.J., et al. Harmonics estimation in power distribution system: the case of a Nigeria University. in 2021 1st International conference on multidisciplinary engineering and applied science (ICMEAS). 2021. IEEE.
  289. Gbadamosi, S.L., N.I. Nwulu, and P. Siano, Harmonics Constrained Approach to Composite Power System Expansion Planning with Large-Scale Renewable Energy Sources. Energies, 2022. 15(11): p. 4070.
  290. Aashwin Prasad, O.S., Harmonic Analysis in Hybrid Power Plant using ETAP Software. International Journal of Computer Applications, July 2022. 184(20): p. 6.
  291. Alyousif, O.M.M., Electrical Power System Harmonics Analysis Using ETAP. Al-Rafidain Engineering Journal (AREJ), 2022. 27(1): p. 90-98.
  292. Hoo, D.S., et al., Mitigation of harmonic distortions in third rail electrical systems. International Journal of Power Electronics and Drive Systems, 2023. 14(1): p. 348.
  293. Ikonwa, W., et al., Harmonic Analysis of 132/33/11 KV Distribution Network Using Etap.
  294. Ikonwa, W., et al., Performance Evaluation and Analysis of Harmonic Filter on Power Network for Improved Power Quality. International Research Journal of Innovations in Engineering and Technology, 2023. 7(3): p. 10.
  295. Farooq, H., et al., Investigating the power quality of an electrical distribution system stressed by non-linear domestic appliances. Renewable Energy and Power Quality Journal, 2011. 1(9).
  296. Awadalla, M., M. Omer, and A. Mohamed. Single-tuned filter design for harmonic mitigation and optimization with capacitor banks. in 2015 International Conference on Computing, Control, Networking, Electronics and Embedded Systems Engineering (ICCNEEE). 2015. IEEE.
  297. Hameed, Z., et al., Harmonics in Electrical Power Systems and how to remove them by using filters in ETAP. Faculty of Engineering and Technology Superior University Pakistan, 2016.
  298. Pang, Y. and Y. Xu. Analysis and treatment of harmonic in power network with railway based on ETAP software. in 2016 IEEE PES Asia-Pacific Power and Energy Engineering Conference (APPEEC). 2016. IEEE.
  299. Riaz, M.T., et al. Analysis and evaluating the effect of harmonic distortion levels in industry. in 2021 4th International Conference on Energy Conservation and Efficiency (ICECE). 2021. IEEE.
  300. Braide, S., Evaluation and Analysis of Harmonic Distortion on 330kV Network Case Study Selected Sub-Region Nigerian Power System for Improve Power Quality. Journal of Progress in Engineering and Physical Science, 2022. 1(1): p. 13-22.
  301. Patil, G.A., Y. Bhosale, and V. Bolaj. Passive filter design to mitigate harmonics in three phase induction furnace. in 2017 International Conference on Circuit, Power and Computing Technologies (ICCPCT). 2017. IEEE.
  302. Milovanović, M., et al., Power flow in radial distribution systems in the presence of harmonics. 2019.
  303. Mahiwal, L.G. and J.G. Jamnani. Analysis and Mitigation of Harmonics for Standard IEEE 13 Bus Test System Using ETAP. in 2019 International Conference on Computing, Power and Communication Technologies (GUCON). 2019. IEEE.
  304. Weibo, K., et al. Simulation and analysis of resonance characteristics of MIDC systems based on ETAP. in International Conference on Renewable Power Generation (RPG 2015). 2015. IET.
  305. Muhammad, T.K., M. Aree Akram, and S. Electrical Eng, Performance improvement of interconnected 400kV, 50Hz Kurdistan and Iraq power systems using proposed HVDC link. ZANCO Journal of Pure and Applied Sciences, 2019. 31: p. 131-136.
  306. Plihal, K., et al. A study on the implementation of HVDC for Power system interconnection. in 2019 6th International Symposium on Electrical and Electronics Engineering (ISEEE). 2019. IEEE.
  307. Kim, C.-h., et al., Electric power system design and analysis for drilling rigs. Journal of Advanced Marine Engineering and Technology (JAMET), 2012. 36(7): p. 942-947.
  308. Farooq, U., et al., Load Flow Analysis of 11 kV Test feeder with and without the injection of DG. International Journal of Computer Science and Information Security, 2017. 15(3): p. 1.
  309. Baby, K. and K. Sreekumar, Load flow analysis of 66 kv substation using Etap software. International Research Journal of Engineering and Technology (IRJET), 2017. 4(02).
  310. Idoniboyeobu, D. and C. Ibeni, Analysisfor Electical Load Flow Studies in Port Harcourt, Nigeria, Using Newton Raphson Fast Decoupled Techniques. American Journal of Engineering Research, 2017. 6(12): p. 230-240.
  311. Mumtaz, M., et al. Load flow analysis of cigre benchmark model using etap. in Proceedings of the International Conference on Renewable, Applied and New Energy Technologies, ICRANET. 2018.
  312. Alvi, A.A. and M.A. Mannan, Load flow analysis of dhaka grid using PSAT and ETAP and performance comparison to PGCB Data. AIUB Journal of Science and Engineering (AJSE), 2019. 18(3): p. 81-87.
  313. Ghiasi, M., E. Ahmadinia, and R. Ghiasi, A case study of modeling, simulation, and load flow assessment in the power distribution network of tehran metro using ETAP. International Journal of Engineering and Future Technology, 2019. 16(3).
  314. Humagain, S., et al., Load Flow Analysis of Under Construction Hydropower Plants in Integrated Nepal Power System. 2020.
  315. Kamble, C.S. and P. Rewatkar, Load-flow Analysis of Distribution systems using ETAP. International Journal of Advanced Engineering, Management and Science, 2017. 2: p. 333-334.
  316. Chowdhury, M.S.H., et al., Design of 2500 KVA 11/0.4 KV Distribution Substation Based on Load Flow Analysis Using ETAP Software.
  317. Irokwe, N. and E. Amako, Electrical Load Flow Analysis for improved power supply to Opolo Community in Bayelsa State using ETAP.
  318. R. Tayshete, S.T., H. Sawant, S. Upalekar, I. Patel, Load Flow Studies of 33/11KV Harbour Substation Ratnagiri Using ETAP. INTERNATIONAL JOURNAL OF PROGRESSIVE RESEARCH IN SCIENCE AND ENGINEERING, 2021. 2(3): p. 1-4.
  319. MEHTRE, V.V. and U. CHAURASIA, Load Flow Analysis of 66 kV substation using ETAP Software. 2022.
  320. Saed, A. and A. Nouh. Modeling and Load Flow Analysis for Al-Bayda City Network Integrating Battery Energy Storage and Photovoltaic System. in 2022 International Conference on Engineering & MIS (ICEMIS). 2022. IEEE.
  321. Pardeshi, D.B., A. Deshpande, and S.V. Chaudhari. Load Flow Analysis of 6 MW Biomass Power Plant. in Information and Communication Technology for Competitive Strategies (ICTCS 2020) ICT: Applications and Social Interfaces. 2022. Springer.
  322. Ogbonna, B.O. and E.T. Oniyeburutan, Power Flow Analysis of 33/11kV, 15MVA Borokiri Injection Substation.
  323. Ganesh, A., et al., Power & Voltage Profile Detection for Water Treatment Plant Electric Network by Performing Load Flow Analysis Using ETAP Software.
  324. Ikonwa, W., H. Amadi, and B. Dike, Load Flow Analysis of 132/33KV Power Network for Voltage Enhancement Using Static VAR Compensation (SVC) Technique. Iconic Research Engineering Journals, 2023. 6(8): p. 2456-8880.
  325. Klungtong, S. and C. Chompoo-inwai. Power flow monitoring and analysis for 24.6 MW at 6.9 kV bus Diesel Power Plant (DPP) using ETAP. in 2016 International Conference on Smart Grid and Clean Energy Technologies (ICSGCE). 2016. IEEE.
  326. Ghiasi, M., et al., A Comparison of Common Power Flow Techniques of the Power Distribution System of Tehran Metro Using ETAP (A Case Study).
  327. Ghiasi, M., A comparative study on common power flow techniques in the power distribution system of the Tehran metro. Tehnički glasnik, 2018. 12(4): p. 244-250.
  328. Hartani, M., et al. Power Flow Analyses of a Standalone 5-Buses IEEE DC Microgrid for Arid Saharian Zone (South of Algeria). in International Conference in Artificial Intelligence in Renewable Energetic Systems. 2019. Springer.
  329. Sumarno, E., K. Handono, and K. Indrakoesoema. Power Flow Analysis on RDE Fuel Handling System Using ETAP. in Journal of Physics: Conference Series. 2019. IOP Publishing.
  330. Ghore, V., et al., Comparative Study Between Newton-Raphson And Gauss-Seidel Method For Power Flow Analysis.
  331. Delelegn, M., R.K. Hiremath, and C.S. Reddy. Power Flow Analysis of Addis-Djibouti Railway Power Supply System Using ETAP. in 2021 IEEE Southern Power Electronics Conference (SPEC). 2021. IEEE.
  332. Abu-Jasser, A., H. El-Ghussain, and H. Mughari. Power flow analysis of a 22/0.4 kv distribution transformer using etap software case study: Al fairoz residential area in the gaza city. in 2021 International Conference on Electric Power Engineering–Palestine (ICEPE-P). 2021. IEEE.
  333. ETUKAFIA, E.A., D. IDONIBOYEOBU, and S. BRAIDE, Analysis and Evaluation of Eket 132/33kv Transmission Station Loading Profiles for Consumer Power Utilization. 2023.
  334. Ramesh, L., et al., Intelligent DE algorithm for measurement location and PSO for bus voltage estimation in power distribution system. International Journal of Electrical Power & Energy Systems, 2012. 39(1): p. 1-8.
  335. Singh, D.K. and S. Gupta. Use of genetic algorithms (GA) for optimal coordination of directional over current relays. in 2012 Students Conference on Engineering and Systems. 2012. IEEE.
  336. Malik, M.N., et al., Load flow analysis of an EHT network using ETAP. Journal of Multidisciplinary Engineering Science and Technology (JMEST), 2016. 3: p. 4979-4984.
  337. Ulinuha, A., A.T. Idayanto, and A. Hanafiyah, ACCURACY OF MATLAB SELF-CODED PROGRAM FOR POWER FLOW ANALYSIS IN COMPARISON WITH STANDARD SOFTWARE PACKAGES. 2009.
  338. Mahiwal, L.G., J.G. Jamnani, and K.N. Velani. Short Circuit Analysis of Electrical Distribution System for Typical Chemical Industry. in 2019 International Conference on Computing, Power and Communication Technologies (GUCON). 2019. IEEE.
  339. Latt, A.Z., Short Circuit Analysis of 33/11/0.4 kV Distribution System Using ETAP. International Journal of Latest Technology in Engineering, Management & Applied Science (IJLTEMAS) Volume, 2019. 8: p. 79-85.
  340. Patil, B. and S. Namekar, Load Flow & Short Circuit Analysis of 132/33/11KV Substation using ETAP. International Journal of Applied Engineering Research, 2018. 13(11): p. 9943-9952.
  341. Zeggai, A. and F. Benhamida. Power flow and Short circuit of 220 kV Substation using ETAP. in 2019 Algerian Large Electrical Network Conference (CAGRE). 2019. IEEE.
  342. Ismail, E. and T. Sindhu. Self-healing practice for an LT 11 kV overhead radial distribution network feeder. in 2013 International Conference on Power, Energy and Control (ICPEC). 2013. IEEE.
  343. Goh, H., et al., Combination of TOPSIS and AHP in load shedding scheme for large pulp mill electrical system. International Journal of Electrical Power & Energy Systems, 2013. 47: p. 198-204.
  344. Lakra, P. and M. Kirar. A comparison of Under Frequency Relay based and Frequency Response model based Load Shedding scheme. in 2015 Annual IEEE India Conference (INDICON). 2015. IEEE.
  345. Khatua, S. and V. Mukherjee, Application of PLC based smart microgrid controller for sequential load restoration during station blackout of nuclear power plants. Annals of Nuclear Energy, 2021. 151: p. 107899.
  346. Kulkarni, S. and S. Sontakke, Power system analysis of a microgrid using ETAP. International Journal of Innovative Science and Modern Engineering, 2015. 10.
  347. Saad, S.M., N. El-Naily, and F.A. Mohamed, A new constraint considering maximum PSM of industrial over-current relays to enhance the performance of the optimization techniques for microgrid protection schemes. Sustainable cities and society, 2019. 44: p. 445-457.
  348. Chandraratne, C., et al., Adaptive protection for microgrid with distributed energy resources. Electronics, 2020. 9(11): p. 1959.
  349. Shah, R., P. Goli, and W. Shireen. Adaptive protection scheme for a microgrid with high levels of renewable energy generation. in 2018 Clemson University Power Systems Conference (PSC). 2018. IEEE.
  350. Alasali, F., et al., Highly sensitive and fast microgrid protection using optimal coordination scheme and nonstandard tripping characteristics. International Journal of Electrical Power & Energy Systems, 2021. 128: p. 106756.
  351. El-Naily, N., et al., Innovative Adaptive Protection Approach to Maximize the Security and Performance of Phase/Earth Overcurrent Relay for Microgrid Considering Earth Fault Scenarios. Electric Power Systems Research, 2022. 206: p. 107844.
  352. Bagul, P.P. and S.M. Akolkar. Relay coordination in microgrid. in 2017 international conference on computing methodologies and communication (ICCMC). 2017. IEEE.
  353. Singh, U., et al. Micro-Grid Relay Coordination Using ETAP. in 2022 2nd International Conference on Advance Computing and Innovative Technologies in Engineering (ICACITE). 2022. IEEE.
  354. Swathika, O. and S. Hemamalini, Relay Coordination in Real-Time Microgrid for varying load demands. ARPN Journal of Engineering and Applied Sciences, 2016. 11(5): p. 3222-3227.
  355. Hosseinzadeh, N., et al., Constructing a multi-microgrid with the inclusion of renewable energy in Oman's rural power system. 2018.
  356. Azeem, F., et al., A two-way pre-installation assessment framework for microgrids under power systems expansion planning. Sustainable Energy Technologies and Assessments, 2023. 55: p. 102920.
  357. Bawayan, H. and M. Younis, Mitigating low fault current in microgrids through renewables-battery hybrid units. International Journal of Electrical Power & Energy Systems, 2023. 145: p. 108611.
  358. Izzatillaev, J., Determination of power flows in microgrids with renewable energy sources by using special computer programs. Applied Solar Energy, 2020. 56: p. 149-155.
  359. Makola, C., P. Le Roux, and J. Jordaan. Design, Analysis, and Operation of Photovoltaic Power in a Microgrid with an EESS. in 2021 IEEE PES/IAS PowerAfrica. 2021. IEEE.
  360. Hanafy, A.M., K.H. Youssef, and N.H. Abbasy. A unified method for fault location in multi-voltage microgrids. in 2021 IEEE Power and Energy Conference at Illinois (PECI). 2021. IEEE.
  361. Medam, R.R., K. Kavitha, and T. Chandrashekar. Techno-economic analysis of hybrid renewable energy based community microgrid. in 2021 IEEE Mysore Sub Section International Conference (MysuruCon). 2021. IEEE.
  362. Ramelan, A., et al. Interconnection System Simulation Analysis of Transient Micro-grid Stability in Indonesia. in 2021 International Conference on ICT for Smart Society (ICISS). 2021. IEEE.
  363. Lata, K., et al. ETAP Based Analysis of 13-Bus Microgrid. in 2022 International Conference for Advancement in Technology (ICONAT). 2022. IEEE.
  364. Zografopoulos, I., et al., Time series-based detection and impact analysis of firmware attacks in microgrids. Energy Reports, 2022. 8: p. 11221-11234.
  365. REDDY, K., et al., Short Circuit Analysis in Microgrid with Renewable Energy Sources by Using ETAP. International Journal of Grid and Distributed Computing, 2020. 13(2): p. 1454-1461.
  366. Hartani, M., et al. Static-Dynamic Analysis of an LVDC Smart Microgrid for a Saharian-Isolated Areas Using ETAP/MATLAB Software. in Smart Energy Empowerment in Smart and Resilient Cities: Renewable Energy for Smart and Sustainable Cities. 2020. Springer.
  367. Khan, K.R., et al., Condition monitoring of a campus microgrid elements using smart sensors. Procedia Computer Science, 2019. 163: p. 109-116.
  368. Abdel-Salam, M., et al., Improvement of protection coordination for a distribution system connected to a microgrid using unidirectional fault current limiter. Ain Shams Engineering Journal, 2017. 8(3): p. 405-414.
  369. Osita, O., P.I. Obi, and I.K. Onwuka, Induction motor starting analysis and start aided device comparison using ETAP. European Journal of Engineering and Technology Research, 2017. 2(7): p. 1-7.
  370. Kirar, M.K. and G. Agnihotri, Emergency Generator Sizing and Motor Starting Analysis. International Journal of Electrical and Computer Engineering, 2013. 7(1): p. 71-76.
  371. Blyuk, V., M. Ershov, and A. Komkov. Models and algorithms for quick calculation of electromechanical transition processes of multi-machine electrotechnical systems. in 2019 1st International Conference on Control Systems, Mathematical Modelling, Automation and Energy Efficiency (SUMMA). 2019. IEEE.
  372. Kirar, M.K. and G. Aginhotri. Cable sizing and effects of cable length on dynamic performance of induction motor. in 2012 IEEE Fifth Power India Conference. 2012. IEEE.
  373. Mahmood, F.M. and M.R. Hashjin, Starting Analysis of Squirrel Cage Induction Motors 1000 kW by Variable Frequency Drive in Power System Case study: Tabriz Pump station. 2022.
  374. Liang, X. and O. Ilochonwu, Induction motor starting in practical industrial applications. IEEE Transactions on Industry Applications, 2010. 47(1): p. 271-280.
  375. Shwehdi, M.H., S.R. Mohamed, and D. Devaraj, Optimal capacitor placement on West–East inter-tie in Saudi Arabia using genetic algorithm. Computers & Electrical Engineering, 2018. 68: p. 156-169.
  376. Tahir, M., et al., Optimal capacitor placement in a distribution system using ETAP software. Indones. J. Electr. Eng. Comput. Sci, 2019. 15(2): p. 650-660.
  377. Al-Refai, S.M. and A.H. Rafa. The optimum location of capacitor to improve the voltage of 220/66 kV Substation Using ETAP Software. in 2022 IEEE 2nd International Maghreb Meeting of the Conference on Sciences and Techniques of Automatic Control and Computer Engineering (MI-STA). 2022. IEEE.
  378. Aziz, E.A.F.A., Studying of Wind farm performance at Zafarana Egypt. Int J Electr Comput Sci IJECS, 2011. 11: p. 42-51.
  379. Pranitha, M. and K.V. Chandrakala. Optimal capacitor placement based improved reliability assessment of a distribution system. in 2017 International Conference on Intelligent Computing and Control (I2C2). 2017. IEEE.
  380. Ghiasi, M. and J. Olamaei, Optimal capacitor placement to minimizing cost and power loss in Tehran metro power distribution system using ETAP (A case study). Complexity, 2016. 21(S2): p. 483-493.
  381. KOUR, G., OPTIMAL PLACEMENT OF STATIC VAR COMPENSATORS IN POWER SYSTEM.
  382. Mukherjee, S., et al. Load Flow Analysis and Reactive Power Compensation. in 2018 International Conference on Computing, Power and Communication Technologies (GUCON). 2018. IEEE.
  383. Airoboman, A., et al. Compensation and Enhancement of the Nigerian Power Systems Network. in 2019 IEEE PES/IAS PowerAfrica. 2019. IEEE.
  384. Idoniboyeobu, D., S. Braide, and G. Sepribo, www. globalscientificjournal. com. GSJ, 2021. 9(9).
  385. Musyoka, E.M. and C.-k. Chang, ANN Based Model for Current Transformers’ Saturation Error Compensation in Medium Voltage Switchgears. Journal of Electrical Engineering & Technology, 2022. 17(4): p. 2171-2179.
  386. Hossin, F., G. Lacey, and R.I. Chowdhury. An Analysis Of Power Quality Improvement By Reactive Power Compensation Devices. in 2022 57th International Universities Power Engineering Conference (UPEC). 2022. IEEE.
  387. Samir, O., et al., Effect of Series/Shunt Capacitors on the Performance of a Distribution Network with Motor Driven Loads. Electric Power Systems Research, 2022. 213: p. 108745.
  388. Sukumaran, S., et al., Optimal Power Flow Analysis for 23MW Microgrid using ETAP. International Journal of Innovative Science and Research Technology, 2018. 3(3): p. 570-575.
  389. Nivedha, R., R, Sreevidya. L, V. Geetha, R. Deepa,“Design of Optimal Power System Stabilizer Using ETAP”. International, Journal of Power System Operation and Energy Management,, ISSN (PRINT): p. 2231-4407.
  390. El Moursi, M. and G. Joos, Optimal tracking secondary voltage control for the DFIG wind turbines and compensator devices. Electric power systems research, 2009. 79(12): p. 1705-1716.
  391. Karegar, H.K. and B. Alinejad. On-Line transmission line zero sequence impedance estimation using Phasor Measurement Units. in 2012 22nd Australasian Universities Power Engineering Conference (AUPEC). 2012. IEEE.
  392. Ahmed, W., et al. Simulated Testing Algorithm for µPMU Full Observation of Balanced Radial Distribution Grid. in 2019 IEEE 7th International Conference on Smart Energy Grid Engineering (SEGE). 2019. IEEE.
  393. Khair, A., et al. PMU assisted state estimation in distribution system with PV penetration. in 2019 International Conference on Electrical, Electronics and Computer Engineering (UPCON). 2019. IEEE.
  394. Ahmed, W., M. Nayel, and M.T. El-Mohandes. A $\mu PMU $ Full Observation Algorithm for Balanced Radial Distribution Grid with PV Integration. in 2021 22nd International Middle East Power Systems Conference (MEPCON). 2021. IEEE.
  395. Ahmed, W., et al., Simulated testing algorithm for µPMU full observation of unbalanced radial distribution grid. Electric Power Systems Research, 2021. 191: p. 106842.
  396. Ramesh, L. and N. Chakraborty, Optimal allocation of transformer and its effects on distribution system loss minimization. Russian Electrical Engineering, 2019. 90: p. 285-293.
  397. Yaabari, N., O.P. Otubu, and O. Ojah, Impact of High Voltage Transmission on I2R Losses Using a Simplified ETAP Model. American Journal of Engineering, 2021. 10: p. 208-213.
  398. Okorie, N., D. Idoniboyeobu, and S. Braide, Optimization of Energy Efficiency for Electric Power Distribution System Losses. International Journal for Research in Applied Science and Engineering Technology, 2021. 9: p. 12.
  399. Sultana, A., S. Ahmad, and A. Shoukat. Technical Losses Evaluation in Power Distribution Network Considering Repairing Fault Period. in 2022 International Conference on Technology and Policy in Energy and Electric Power (ICT-PEP). 2022. IEEE.
  400. Al-Mahroqi, Y., et al., Reduction of power losses in distribution systems. International Journal of Computer and Systems Engineering, 2012. 6(3): p. 315-322.
  401. Soni, C., P. Gandhi, and S. Takalkar. Design and analysis of 11 KV distribution system using ETAP software. in 2015 International Conference on Computation of Power, Energy, Information and Communication (ICCPEIC). 2015. IEEE.
  402. Pillay, A., et al. Analysis on power distribution system in India-Patna city-A case study. in 2014 International Conference on Computation of Power, Energy, Information and Communication (ICCPEIC). 2014. IEEE.
  403. Gheydi, M., et al. Comparative assessment of power loss among four typical wind turbines in power distribution system. in 2016 International Symposium on Fundamentals of Electrical Engineering (ISFEE). 2016. IEEE.
  404. Sujatha, S. and R. Anita, Power quality enhancement by using SVC in real time power system. 2015.
  405. Gujar, N.S. and S.K. Talati. Power quality monitoring and mitigation. in 2017 7th International Conference on Power Systems (ICPS). 2017. IEEE.
  406. Dineshkumar, J., M. Dineshkumar, and M.P.M.M. Dineshkumar, Transient Stability Analysis and Power Quality Improvement One Thirty Two KV using ETAP.
  407. Sun, F., et al. Case analysis of power quality impact assessment and governance of electrified railway based on ETAP software. in IOP Conference Series: Earth and Environmental Science. 2020. IOP Publishing.
  408. Almaktar, M., et al. Power Quality Assessment of Karabuk University'S Grid-Connected Microgrid Under High Penetration of PV Generation. in 2022 International Symposium on Multidisciplinary Studies and Innovative Technologies (ISMSIT). 2022. IEEE.
  409. Absar, M.N., M.F. Islam, and A. Ahmed, Power quality improvement of a proposed grid-connected hybrid system by load flow analysis using static var compensator. Heliyon, 2023. 9(7).
  410. Cahyadi, D.R. and I.G.I. Garniwa, Analysis Of Modern Railway Power Quality Conditions With Inspection Methods To Mitigate Operating System Failures Referring To Regulations And Standard References. Journal of Social Science (JoSS), 2023. 2(7): p. 552-566.
  411. Katar, C. and C.P. Uzunoğlu, A comparative study on AC/DC analysis of an operational low voltage distribution system. Int. J. Appl. Power Eng, 2021. 10: p. 193-206.
  412. Liu, K. and J. Chen. Research on Application of ETAP in Ship electric propulsion system. in E3S Web of Conferences. 2021. EDP Sciences.
  413. Patel, R.N., P.R. Gandhi, and K. Velani. Power Distribution Network Analysis of High-Rise Building using ETAP. in 2019 International Conference on Intelligent Computing and Control Systems (ICCS). 2019. IEEE.
  414. Ray, S. and A.K. Jha. Grid Integration Studies of Captive and Cogeneration Plant in Sugar Industry: Case Study of Indushankar Sugar Industry Pvt. Ltd. in IOE Graduate Conference. 2017.
  415. Manickam, R. and S.N. Palaniappan, Upgrading transmission line capability by AC–DC conversion. Computers & Electrical Engineering, 2018. 68: p. 616-628.
  416. El-Refaie, E.-S.M., et al., Achievement of the best design for unequally spaced grounding grids. Ain Shams Engineering Journal, 2015. 6(1): p. 171-179.
  417. Bobric, E., et al. Web-Based Laboratory for Modeling and Simulation of Power System. in 2019 17th International Conference on Emerging eLearning Technologies and Applications (ICETA). 2019. IEEE.
  418. Idoniboyeobu, D., S. Braide, and I. Chukwuma, ENHANCEMENT OF ELECTRIC POWER SUPPLY TO ABULOMA COMMUNITY IN PORT HARCOURT FOR IMPROVED PERFORMANCE. GSJ, 2021. 9(7).
  419. Majidov, A., A.G. Kayumov, and S. Hafizov. Investigation of the Self-Starting Process of a Low-Power Asynchronous Motor. in 2021 IEEE Conference of Russian Young Researchers in Electrical and Electronic Engineering (ElConRus). 2021. IEEE.
  420. Gómez-Ramírez, G.A., et al. Demand response improvement using storage power systems: Case study of honduras. in 2021 IEEE CHILEAN Conference on Electrical, Electronics Engineering, Information and Communication Technologies (CHILECON). 2021. IEEE.
  421. Braide, S. and D.I.G. Gomene, EVALUATION OF TRANSMISSION DISTRIBUTION POWER OUTAGES IN NIGERIA POWER NETWORK FOR IMPROVED PERFORMANCE (A Case of Afam Power Generation Station to Port Harcourt Mains Trans-Amadi). GSJ, 2021. 9(8).
  422. Shi, Y., et al., Safety analysis and dynamic risk assessment of community power distribution network using Bayesian network. IFAC-PapersOnLine, 2022. 55(6): p. 583-590.
  423. Krishna, G.A.G. and C. Babulal. Demand Response: A Tool for Flexibility Creation in the Electricity Market. in 2022 Third International Conference on Intelligent Computing Instrumentation and Control Technologies (ICICICT). 2022. IEEE.
  424. Rajashekar, Y., et al. Techniques for practical qualitative approach using commercial power system simulation software for industrial applications. in 2017 7th International Conference on Power Systems (ICPS). 2017. IEEE.
  425. Saber, A.Y. Power system stabilizer tuning using swarm based optimization in ETAP. in 2014 IEEE International Conference on Power Electronics, Drives and Energy Systems (PEDES). 2014. IEEE.
  426. Sauhats, A., et al. Detection and Management of Large Scale Disturbances in Power System. in Critical Information Infrastructures Security: 9th International Conference, CRITIS 2014, Limassol, Cyprus, October 13-15, 2014, Revised Selected Papers 9. 2016. Springer.
  427. Klyachko, L., et al., A Model of a Combined Subway Traction Substation Taking Traction Load and Consumers’ Auxiliaries into Account. Russian Electrical Engineering, 2021. 92(9): p. 488-491.
  428. Shevlyugin, M., et al., Electric stock digital twin in a subway traction power system. Russian Electrical Engineering, 2019. 90: p. 647-652.
  429. Patoding, H.E. and M. Sau. Additional location scenarios of generation capacity with ETAP application. in IOP Conference Series: Materials Science and Engineering. 2020. IOP Publishing.
  430. Tulsky, V., et al. Application of ETAPTM eTraXTM software package for digital simulation of distribution network that feeds an AC traction power supply system. in E3S Web of Conferences. 2020. EDP Sciences.
  431. Liu, J., et al. Study of effects on power system relay protection by harmonic and negative sequence components of electrified rails. in 2016 International Conference on Advanced Electronic Science and Technology (AEST 2016). 2016. Atlantis Press.
  432. Lakshmi, S.G. and S.S. Kumar. Integrated substation automation and monitoring system. in 2013 IEEE International Conference on Computational Intelligence and Computing Research. 2013. IEEE.
  433. Yilmaz, E.N. and B. Baygüneş. Design, analysis and optimization of 1350 MW natural gas thermal power plant. in 2017 5th International Istanbul Smart Grid and Cities Congress and Fair (ICSG). 2017. IEEE.
  434. Xu, Q., et al., A Rigorous Method for Power Quality Evaluation of High-speed Railway Using Electrical Transient Analyzer Program. Przegląd Elektrotechniczny, 2012. 88(11a): p. 248-252.
  435. Paleongan, Y. and I. Nungtjik. Analysis of voltage transient behaviour of generators connected on medium voltage distribution system. in 2011 International Conference on Advanced Power System Automation and Protection. 2011. IEEE.
  436. Benfatto, I., et al., Tools for the design integration of the ITER power supplies and electrical installations. Fusion engineering and design, 2011. 86(6-8): p. 1537-1540.
  437. Makani, Z. and S.D. Chowdhury. Design of electrical power supply system in a typical petroleum refinery. in 2017 52nd International Universities Power Engineering Conference (UPEC). 2017. IEEE.
  438. Zala, Y. Comparative study and simulative analysis of high voltage and low voltage distribution systems for rural agricultural loads: Simulation using etap software. in 2017 IEEE International Conference on Smart Energy Grid Engineering (SEGE). 2017. IEEE.
  439. Hwang, S.-H., et al. Vulnerability analysis for open phase condition in electric power system of Korea's nuclear power generating station. in 2017 International Conference on Circuits, System and Simulation (ICCSS). 2017. IEEE.
  440. Ch. Siva Kumari, S.R., Power System Modelling and Analysis of a Combined Cycle Power Plant Using ETAP. International Research Journal of Engineering and Technology (IRJET), 2016. 03(06): p. 1331-1335.
  441. Faulkner, A., et al. Load flow, short circuit analysis and load point reliability for Data Centre power distribution networks. in 2018 IEEE Industry Applications Society Annual Meeting (IAS). 2018. IEEE.
  442. Shah, K.B., S.K. Rathor, and R. Mehta. Industrial grade power system study analysis. in 2016 International Conference on Electrical, Electronics, and Optimization Techniques (ICEEOT). 2016. IEEE.
  443. Natkar, K. and N. Kumar, Design analysis of 220/132 KV substation using ETAP. International Research Journal of Engineering and Technology (IRJET), 2015. 2(3): p. 2322-2326.
  444. Bhatia, K., Feasibility Studies on the Proposed Developments to Be Added In the Existing Electrical Network by Using ETAP.
  445. Zeggai, A. and F. Benhamida. Power flow and Short circuit of a Real Eectrolysis Plant. in 2019 Algerian Large Electrical Network Conference (CAGRE). 2019. IEEE.
  446. Zeggai, A. and F. Benhamida, Power flow and Short circuit with different load and contingency scenarios of an electrolysis plant.
  447. Muzzammel, R. and R. Arshad, Comprehensive analysis and design of furnace oil-based power station using ETAP. Int. J. Appl, 2022. 11: p. 33-51.
  448. Ullah, M.A., et al. Power flow & voltage stability analyses and remedies for a 340 MW nuclear power plant using ETAP. in 2017 International Conference on Electrical Engineering (ICEE). 2017. IEEE.
  449. Zeggai, A., F. Benhamida, and R. Bouddou, Power System Analysis of Seawater Desalination Plant in Algeria with Different Load Scenarios. Journal Européen des Systèmes Automatisés, 2021. 54(3).
  450. Dey, B., et al., Load Flow Analysis and Transient System Analysis of A Cycle Combined Power Plant Using ETAP Software. Available at SSRN 4108082, 2022.
  451. Alasady, S., R. Almansory, and H. Alrudainy. Analysis of Load flow and Transient stability of 10-bus multi-machine system with PV penetration. in IMDC-IST 2021: Proceedings of 2nd International Multi-Disciplinary Conference Theme: Integrated Sciences and Technologies, IMDC-IST 2021, 7-9 September 2021, Sakarya, Turkey. 2022. European Alliance for Innovation.
  452. Nisar, N., et al. Analysis and optimization of 132KV grid using ETAP. in 2015 Power Generation System and Renewable Energy Technologies (PGSRET). 2015. IEEE.
  453. Kareem, M.S.A. and S. Gheorghe. Power flow analysis in power system planning. case study. in 2019 International Conference on ENERGY and ENVIRONMENT (CIEM). 2019. IEEE.
  454. Jaleel, J.A. and S. Shabna, Load flow analysis and reliability evaluation of 220kV Kerala power system. International journal of engineering and innovative technology (IJEIT), 2013. 3(2): p. 558-563.
  455. Mahdi, N.M., Power flow analysis of Rafah governorate distribution network using ETAP software. International Journal of Physical Sciences, 2013. 1(2): p. 019-026.
  456. Ullah, N., et al., Electric Supply Substation Simulation using ETAP Software. University of Sindh Journal of Information and Communication Technology, 2018. 2(4): p. 176-179.
  457. Alam, M.A., et al. Designing of an Underwater Power Transmission System and Hybrid Power Supply for an Isolated Island of Bangladesh: Swarna Dwip. in 2021 International Conference on Science & Contemporary Technologies (ICSCT). 2021. IEEE.
  458. Nasir, M. and A.A. Bhatti. A micro computer-based methodology for distance protection on long UHV transmission lines using symmetrical components. in 2012 Asia-Pacific Power and Energy Engineering Conference. 2012. IEEE.
  459. Yang, M.-T. and J.-C. Gu, Optimal coordination of automatic line switches for distribution systems. Energies, 2012. 5(4): p. 1150-1174.
  460. Qi, X.-q., et al. Influence of the parameter settings of inverter's protection system on isolated grid operation with photovoltaic power station connected. in IEEE PES Innovative Smart Grid Technologies. 2012. IEEE.
  461. Hernanda, I.S., et al. Analysis of protection failure effect and relay coordination on reliability index. in 2014 The 1st International Conference on Information Technology, Computer, and Electrical Engineering. 2014. IEEE.
  462. Asrari, A. and B. Ramos. Power system protection upgrade at anclote plant a case study in Florida state. in 2018 IEEE Texas Power and Energy Conference (TPEC). 2018. IEEE.
  463. Dashti, R., S. Hassani, and H.R. Shaker. Protection coordination assessment and improvement of electrical network of an industrial complex in connection to power grid: An experience report. in 2018 5th International Conference on Electrical and Electronic Engineering (ICEEE). 2018. IEEE.
  464. Parra, P., et al. Feeder configuration and coordination of protections for an electric substation. in 2018 IEEE International Conference on Automation/XXIII Congress of the Chilean Association of Automatic Control (ICA-ACCA). 2018. IEEE.
  465. Karimi, H., et al., A protection strategy for inverter-interfaced islanded microgrids with looped configuration. Electrical Engineering, 2019. 101(3): p. 1059-1073.
  466. Khatua, S. and V. Mukherjee, Adaptive overcurrent protection scheme suitable for station blackout power supply of nuclear power plant operated through an integrated microgrid. Electric Power Systems Research, 2021. 192: p. 106934.
  467. Rath, S.S., et al. Protection Study in 9-Generator Power System Under Grid-Connected Mode of Operation. in 2022 International Conference on Intelligent Controller and Computing for Smart Power (ICICCSP). 2022. IEEE.
  468. Chang, C.-k., Adaptive undervoltage protection scheme for safety bus in nuclear power plants. Nuclear Engineering and Technology, 2022. 54(6): p. 2055-2061.
  469. Patel, H.A., V.M. Sharma, and A. Deshpande, Relay Coordination using ETAP. International Journal of Scientific & Engineering Research, 2015. 6(5): p. 1583-1588.
  470. Jayaprakash, J., M. AngelinPonrani, and J. LakshmiR, Planning and coordination of relay in distribution system using Etap. Pakistan Journal of Biotechnology, 2016. 13(special issue 1): p. 252-256.
  471. Mukherjee, S., et al. Analysis on Relay Coordination in IEEE 9 bus PV integrated Hybrid Power System using ETAP software: A case study. in IOP Conference Series: Earth and Environmental Science. 2021. IOP Publishing.
  472. Aliman, O. and I. Musirin. Overcurrent relays coordination for commercial building. in 2013 IEEE 7th International Power Engineering and Optimization Conference (PEOCO). 2013. IEEE.
  473. Pathan, M. and A. Shah. Co-ordination of protective relays for 16MW load system using ETAP. in 2017 International Conference on Energy, Communication, Data Analytics and Soft Computing (ICECDS). 2017. IEEE.
  474. Elbana, M.S., et al., µPMU-based smart adaptive protection scheme for microgrids. Journal of Modern Power Systems and Clean Energy, 2019. 7(4): p. 887-898.
  475. Zhang, Z., Y. Kang, and X. Xie. Online verification method of relay protection settings based on etap software. in IOP Conference Series: Earth and Environmental Science. 2020. IOP Publishing.
  476. Chaudhary, N.P., S. Baral, and B. Adhikary, POWER SYSTEM PROTECTION ASSESSMENT OF A MINI-GRID: CASE OF NEPAL. GSJ, 2020. 8(10).
  477. El-Naily, N., S.M. Saad, and F.A. Mohamed, Novel approach for optimum coordination of overcurrent relays to enhance microgrid earth fault protection scheme. Sustainable Cities and Society, 2020. 54: p. 102006.
  478. Patil, N., et al. Protection of microgrid using coordinated directional overcurrent and undervoltage relay. in 2021 International Conference on Sustainable Energy and Future Electric Transportation (SEFET). 2021. IEEE.
  479. Chandraratne, C., R. Naayagi, and G. Panda. Development and implementation of an adaptive overcurrent protection algorithm for a modern power distribution network. in 2020 3rd International Conference on Energy, Power and Environment: Towards Clean Energy Technologies. 2021. IEEE.
  480. George, S.P. and A. Sankar, Optimal settings for adaptive overcurrent relay coordination in grid-connected wind farms. Electric Power Components and Systems, 2020. 48(12-13): p. 1308-1326.
  481. Ballal, M.S., A.R. Kulkarni, and H.M. Suryawanshi, Operational experience and performance evaluation of some of the system integrity and protection schemes. Electrical Engineering, 2021. 103: p. 1155-1167.
  482. Čonka, Z., et al. Problems related with designing of relay protection for a distribution network containing a local generation unit. in 2021 IEEE 4th International Conference and Workshop Óbuda on Electrical and Power Engineering (CANDO-EPE). 2021. IEEE.
  483. Ballal, M.S., A.R. Kulkarni, and H.M. Suryawanshi, Methodology for the improvements in synchrophasor based System Integrity Protection Schemes under stressed conditions. Sustainable Energy, Grids and Networks, 2021. 26: p. 100465.
  484. Reda, A., et al., Multi-characteristic overcurrent relay of feeder protection for minimum tripping times and self-protection. Electrical Engineering, 2023. 105(2): p. 605-617.
  485. Uddin, M.N., M.S. Arifin, and N. Rezaei, A Novel Neuro-Fuzzy Based Direct Power Control of a DFIG based Wind Farm Incorporated with Distance Protection Scheme and LVRT Capability. IEEE Transactions on Industry Applications, 2023.
  486. Ballal, M.S. and A.R. Kulkarni, Improvements in Existing System Integrity Protection Schemes Under Stressed Conditions by Synchrophasor Technology—Case Studies. IEEE Access, 2021. 9: p. 20788-20807.
  487. Lee, S., et al. Power system modeling and analysis of electric ship propulsion system. in INTELEC 2009-31st International Telecommunications Energy Conference. 2009. IEEE.
  488. Bisheh, H., et al., An adaptive fuse-saving protection scheme for active distribution networks. International Journal of Electrical Power & Energy Systems, 2023. 144: p. 108625.
  489. Khatua, S. and V. Mukherjee, A dynamic hybrid protection scheme for on-site emergency power system operated through an integrated microgrid during station blackout in NPP. Annals of Nuclear Energy, 2023. 182: p. 109615.
  490. Wei, J. Relay Protection Setting Calculation of Power Transformer Based on ETAP. in Journal of Physics: Conference Series. 2023. IOP Publishing.
  491. Ballal, M.S. and A.R. Kulkarni, Integrating synchrophasor technology for the improvements in system integrity protection schemes under stressed conditions. Sādhanā, 2021. 46(4): p. 214.
  492. Aman, M.M., M.Q.A. Khan, and S.A. Qazi, Digital directional and non-directional over current relays: Modelling and performance analysis. NED University Journal of Research, 2011. 8(2): p. 70-85.
  493. Saini, S. Overcurrent relay coordination for phase and earth faults using ETAP. in Proceedings of the 7th IRF International Conference, 27th April, Pune, India. 2014.
  494. Rajput, V.N. and T.M. Vala, Co-ordination of Overcurrent Relay for Chemical Industrial Plant using ETAP. International Journal of Futuristic Trends in Engineering and Technology, 2014. 1(2): p. 1-5.
  495. Thangalakshmi, S., Planning and coordination of relays in distribution system. Indian Journal of Science and Technology, 2016. 9(31): p. 1-7.
  496. Saini, S. Overcurrent relay coordination for phase and earth faults using ETAP. in Electrical and Electronics Department, Amity University (AUUP), Noida, India, Proceedings of IRF International Conference. 2018.
  497. El-Fergany, A.A. and H.M. Hasanien, Water cycle algorithm for optimal overcurrent relays coordination in electric power systems. Soft Computing, 2019. 23(23): p. 12761-12778.
  498. George, S.P. and S. Ashok, Forecast-based overcurrent relay coordination in wind farms. International Journal of Electrical Power & Energy Systems, 2020. 118: p. 105834.
  499. Saleh, M.I., G. El-Saady, and A.M. Yousef. Over current relays setting design using ETAP software taking in to consideration transformer inrush current. in 2021 22nd International Middle East Power Systems Conference (MEPCON). 2021. IEEE.
  500. Draz, A., M.M. Elkholy, and A.A. El-Fergany, Slime mould algorithm constrained by the relay operating time for optimal coordination of directional overcurrent relays using multiple standardized tripping curves. Neural Computing and Applications, 2021. 33: p. 11875-11887.
  501. Ramli, S.P., et al., Optimal coordination of directional overcurrent relay based on combination of Firefly Algorithm and Linear Programming. Ain Shams Engineering Journal, 2022. 13(6): p. 101777.
  502. Mgbeike, V., et al., Over-Current Relay Tripping Coordination in A Power System With High Level Of Distributed Generation (Dg) Considering Islanding Mode.
  503. Saikrishna, R., N.K. Rajalwal, and D. Ghosh, Adaptive relay co-ordination using a busbar splitting approach for a system integrity protection scheme. Protection and Control of Modern Power Systems, 2022. 7(1): p. 14.
  504. Zarour, E., et al., A new adaptive protection approach for overcurrent relays using novel nonstandard current-voltage characteristics. Electric Power Systems Research, 2023. 216: p. 109083.
  505. Sharma, A. and B.K. Panigrahi, Interphase fault relaying scheme to mitigate sympathetic tripping in meshed distribution system. IEEE Transactions on Industry Applications, 2018. 55(1): p. 850-857.
  506. Abu-Siada, A., A novel design for adaptive harmonic filter to improve the performance of over current relays. International Journal of Advances in Engineering & Technology, 2011. 1(5).
  507. Cikan, M. and B. Kekezoglu, Comparison of metaheuristic optimization techniques including Equilibrium optimizer algorithm in power distribution network reconfiguration. Alexandria Engineering Journal, 2022. 61(2): p. 991-1031.
  508. Mohammed, B., USING NETWORK RECONFIGURATION AS A TOOL FOR MITIGATING VOLTAGE SAGS IN PRACTICAL DISTRIBUTION SYSTEMS. Diyala Journal of Engineering Sciences, 2010: p. 463-472.
  509. Shaheen, A.M., A.M. Elsayed, and M. Abd El Aziz. Capacitor switching with distribution system reconfiguration and load variations: Practical case study using ETAP and network analyzer. in 2019 21st International Middle East Power Systems Conference (MEPCON). 2019. IEEE.
  510. Castillo, F., A. Aguila, and J. González, Analysis of stability of tension and losses of electric power in distribution networks with distributed generation. IEEE Latin America Transactions, 2016. 14(11): p. 4491-4498.
  511. Dermawan, E., et al., AI,(2017). Preliminary Study Design Model for Harmonic Filter of Power System Stability Using ETAP Powerstation. ARPN Journal of Engineering and Applied Sciences. 12(16): p. 4684-4688.
  512. Putra, N.P.U., et al. Harmonic Effect for Voltage Stability Condition in Radial Distribution System. in 2019 International Seminar on Intelligent Technology and Its Applications (ISITIA). 2019. IEEE.
  513. Chen, H.-C., S.-Y. Chen, and S.-C. Shih, Transient stability analysis of an industrial cogeneration system. 第五屆智慧生活科技研討會論文集 (下), 2010.
  514. Ibe, A.O. and A. Odia, Transient Stability Assessment of the Nigerian 330kV Network. International Journal of Engineering. 4(5): p. 357.
  515. Monica, A. Transient stability analysis of tngt power system. in 2014 IEEE 8th International Conference on Intelligent Systems and Control (ISCO). 2014. IEEE.
  516. Aswani, R. and R. Sakthivel, Transient Stability Enhancement of 110/11kv Substation using ETAP. International Journal of Innovative Research & Development, 2014. 3(5).
  517. Islam, M.S., M.S. Islam, and M.F. Khan. Effect of variation of different generator parameters on the stability of a small power plant: An analysis through ETAP software. in 2016 3rd International Conference on Electrical Engineering and Information Communication Technology (ICEEICT). 2016. IEEE.
  518. Reddy, D.S. and C.S. Kumari. Transient stability analysis of a combined cycle power plant using etap software. in 2017 IEEE 7th International Advance Computing Conference (IACC). 2017. IEEE.
  519. Latt, A.Z., Transient stability analysis of 3-machine 7-bus system using etap. sTA, 2019. 1: p. 1.
  520. Khatua, S., V. Mukherjee, and R. Ramanavasu. Transient Stability Analysis of Large Capacity Induction Motor-Pump Sets Operated Though an Integrated Microgrid. in 2019 2nd International Conference on Power and Embedded Drive Control (ICPEDC). 2019. IEEE.
  521. Mohammed, M.A., et al. Structure preserving model analysis for power system transient stability. in 2020 International Conference on Electrical, Communication, and Computer Engineering (ICECCE). 2020. IEEE.
  522. Awais, M., et al., Transient Stability Analysis of an HPR-1000 Power Plant using ETAP Software. Pakistan Journal of Engineering and Technology, 2022. 5(2): p. 23-27.
  523. Kuznetsov, O., I. Zubkova, and D. Averyanov, A Global-Energy-Network Equivalent for Calculation of Transient Stability. Russian Electrical Engineering, 2022. 93(1): p. 46-52.
  524. ZEMITTE, S., M. HAMOUDA, and F.Z. ARAMA, Dynamic Stability Analysis with Real Data of Hybrid RES Integration in Southwest Algeria Power System Using Etap Software.
  525. Wu, J., et al. Static Stability Analysis of Ship Power System with S-CO2 Brayton Cycle Power Generation System Integrated. in 2021 6th International Conference on Transportation Information and Safety (ICTIS). 2021. IEEE.
  526. Ikonwa, W., E.C. Obuah, and B. Wokoma, Impact of Static Var Compensator (SVC) on Transient Stability of Power Network in Nigeria. International Research Journal of Innovations in Engineering and Technology, 2023. 7(4): p. 37.
  527. Nallagalva, S.K., M.K. Kirar, and G. Agnihotri, Transient stability analysis of the IEEE 9-bus electric power system. International Journal of Scientific Engineering and Technology, 2012. 1(3): p. 161-166.
  528. Mehra, R., et al. Analysis of PCA based compression and denoising of smart grid data under normal and fault conditions. in 2013 IEEE International Conference on Electronics, Computing and Communication Technologies. 2013. IEEE.
  529. Eseosa, O. and S. Ike, Stability Studies of the Nigerian 330 KV Integrated Power System. Journal of Electrical & Electronics, 2015. 4(1): p. 1.
  530. Siva, A.S., S. Sathieshkumar, and T.S. Kumar. Analysis of stability in IEEE 14 bus system using ETAP Software. in 2020 Fourth International Conference on Inventive Systems and Control (ICISC). 2020. IEEE.
  531. Nagode, K., I. Škrjanc, and B. Murovec, Enhanced stability and failure avoidance of hydropower plant in contingent island operation by model predictive frequency control. Energy Reports, 2022. 8: p. 9308-9330.
  532. Kamdar, R., M. Kumar, and G. Agnihotri, Transient stability analysis and enhancement of IEEE-9 bus system. Electrical & Computer Engineering: An International Journal (ECIJ), 2014. 3(2): p. 41-51.
  533. Islam, M.S. and M.F. Khan, Stability Analysis of a Hybrid Power Plant: An Analysis through ETAP Software. International Journal of Engineering and Technology, 2019. 11(2).
  534. Rahman, S.R., et al. Determining Critical Clearing Time in Transient Stability Assessment for Hybrid Power System. in 2019 IEEE 6th International Conference on Engineering Technologies and Applied Sciences (ICETAS). 2019. IEEE.
  535. Abakar, D., et al., Transient stability analysis of the multimachine power system using ETAP-software. International Journal of Electrical and Electronics Engineering Studies, 2020. 6(1): p. 1-12.
  536. Rajamohamed, S., D. Devaraj, and P.A. Jeyanthy. Modeling and simulating for transient stability analysis of an 380 KV inter-tie network. in 2015 International Conference on Control, Instrumentation, Communication and Computational Technologies (ICCICCT). 2015. IEEE.
  537. Abass, A.Z., D. Pavlyuchenko, and Z.S. Hussain, Survey about impact voltage instability and transient stability for a power system with an integrated solar combined cycle plant in Iraq by using ETAP. Journal of Robotics and Control (JRC), 2021. 2(3): p. 134-139.
  538. Jha, B.K., R.P. Gupta, and U. Prasad, Combined operation of SVC, PSS and increasing inertia of machine for power system transient stability enhancement. American Journal of Electrical Power and Energy Systems, 2014. 3(1): p. 7-14.
  539. Abd-Al Huseen, S. and R. Almansory. Short Circuit and Stability Analysis of a Multi-Machine System with Wind Turbine Using the ETAP Program. in Proceedings of 2nd International Multi-Disciplinary Conference Theme: Integrated Sciences and Technologies, IMDC-IST 2021, 7-9 September 2021, Sakarya, Turkey. 2022.
  540. BRIGGS, K.C., D. Idoniboyeobu, and S. BRAIDE, Study Of Transmission/Distribution Line Interface For Improved Grid Stability Using Moment Distribution Technique.
  541. Akhikpemelo, A., N. Eyibo, and A. Adeyi, Reliability analysis of power distribution network. Continental J. Engineering Sciences, 2016. 11(2): p. 53-63.
  542. Enesi, M.R., et al., Reliability modeling and analysis of high voltage power equipment: a case study of Ajaokuta Steel Company Limited (ASCL). Life Cycle Reliability and Safety Engineering, 2022. 11(4): p. 377-387.
  543. Peter .O. Ohiero, E., Lawrence Effiong, Reliability Assessment of 33KV Power Distribution System -A Case Study of Calabar 33kV Distribution Network. International Journal of Advanced Research in Electrical, Electronics and Instrumentation Engineering (IJAREEIE). 11(5): p. 12.
  544. Maraaba, L., et al., Neural Networks Based Dynamic Load Modeling for Power System Reliability Assessment. Sustainability, 2023. 15(6): p. 5403.
  545. Murthy, C., et al. Distribution automation using wireless communications for improving reliability. in 2011 International Conference on Devices and Communications (ICDeCom). 2011. IEEE.
  546. Ahmad, S., et al., Reliability analysis of distribution system using ETAP. Int J Computer Sci Inf Secure, 2017. 15(3): p. 197-201.
  547. Oreke, F.C. and D. Idoniboyeobu, Reliability Assessment of Electrical Energy Distribution System–A Case Study of Port Harcourt Distribution Network. International Journal for Research in Applied Science Engineering Technology (IJRASET), 2017. 5: p. 432-441.
  548. Ghiasi, M., N. Ghadimi, and E. Ahmadinia, An analytical methodology for reliability assessment and failure analysis in distributed power system. SN Applied Sciences, 2019. 1(1): p. 44.
  549. Avor, J.K. and C.-K. Chang, Reliability analysis of application of variable frequency drive on condensate pump in nuclear power plant. Journal of International Council on Electrical Engineering, 2019. 9(1): p. 8-14.
  550. Soma, S.S. and S.A. Olalekan, Analysis and improvement of reliability in a radial power distribution system using smart reclosers. Journal of Electrical and Electronics Engineering, 2021. 14(1): p. 68-73.
  551. Dat, H.T., N.T.B. Tuyen, and N.N.P. Diem. Evaluation and Improvement Distribution actual network Reliability using ETAP. in 2021 International Symposium on Electrical and Electronics Engineering (ISEE). 2021. IEEE.
  552. Dat, H.T., et al., Research of Distribution Network Reliability Assessment by ETAP Software. GMSARN International Journal, 2022. 16(1): p. 33-46.
  553. Ouyang, J., et al. Identification and Analysis of Key Equipment for Power Supply Reliability of Distribution Network based on ETAP. in 2021 China International Conference on Electricity Distribution (CICED). 2021. IEEE.
  554. Shivam Shukla. Sachin Kumar, M.K.P., Evolution and improvement of power system reliability indices using ETAP software. International Research Journal of Modernization in Engineering Technology and Science, August-2022. 04(08): p. 6.
  555. Bhatti, A., et al., Selection of Power System on the Basis of Best Combination of Power Source and Busbar Scheme. International Journal of Electrical and Electronics, 2013. 118: p. 160-165.
  556. Lee, G., et al., Electric power system design and analysis for FLNG vessel. Journal of Advanced Marine Engineering and Technology (JAMET), 2014. 38(5): p. 573-580.
  557. Zhao, J., et al., An improved complex ICA based method for wind farm harmonic emission levels evaluation. Electric Power Systems Research, 2020. 179: p. 106105.
  558. Mehtre, V.V., S.G. Desai, and D. Bankar. Analysis of a Doubly Fed induction generator based wind farm. in 2016 IEEE Technological Innovations in ICT for Agriculture and Rural Development (TIAR). 2016. IEEE.
  559. Bhadane, K., M. Ballal, and R. Moharil, Power Quality Enhancment of Grid Connected Wind Energy by using Custom Power Devices. RTM Nagpur, 2017.
  560. Bankar, D., S.G. Desai, and V.V. Mehtre. Performance comparison of SCIG and DFIG based wind farm in ETAP. in 2016 International Conference on Automatic Control and Dynamic Optimization Techniques (ICACDOT). 2016. IEEE.
  561. Khani, N.G., et al., Analyzing the effect of wind farm to improve transmission line stability in contingencies. Indian Journal of Science and Technology, 2015. 8(11): p. 1-6.
  562. Ymeri, A., N. Krasniqi, and R. Shaqiri, Impact of the Wind Power Plant Connection to the Kosovo Power System. IFAC-PapersOnLine, 2022. 55(39): p. 393-398.
  563. Hussain, M., A. Hussain, and S. Khan, A comprehensive assessment of the wind power potential of NokKundi in balochistan and its integration with the local electrical grid. Engineering Proceedings, 2022. 12(1): p. 96.
  564. Gheydi, M., et al. Comparative assessment of double-fed induction generator and full converter generator wind turbines on short circuits in distribution systems. in 2015 IEEE 15th International Conference on Environment and Electrical Engineering (EEEIC). 2015. IEEE.
  565. Khan, Z.W., et al. Comparison and analysis of operational modes of a wind generator on distribution network. in 2017 International Conference on Electrical Engineering (ICEE). 2017. IEEE.
  566. Manandhar, P. and N.R. Karki. Impact Analysis of Wind Power System Installation in Kathmandu Valley Network. in Proceedings of IOE Graduate Conference. 2015.
  567. Bhatt, P., Harmonics mitigated multi-objective energy optimization in PV integrated rural distribution network using modified TLBO algorithm. Renewable Energy Focus, 2022. 40: p. 13-22.
  568. Fani, B., H. Bisheh, and A. Karami-Horestani, An offline penetration-free protection scheme for PV-dominated distribution systems. Electric Power Systems Research, 2018. 157: p. 1-9.
  569. Najafabadi, S.R.K., B. Fani, and I. Sadeghkhani, Optimal determination of photovoltaic penetration level considering protection coordination. IEEE Systems Journal, 2021. 16(2): p. 2121-2124.
  570. Jena, A.A., et al. Protection and Relay Coordination Study in Solar Photovoltaic Integrated Hybrid Power System. in 2022 International Conference on Intelligent Controller and Computing for Smart Power (ICICCSP). 2022. IEEE.
  571. Alasali, F., et al., Hybrid tripping characteristic-based protection coordination scheme for photovoltaic power systems. Sustainability, 2023. 15(2): p. 1540.
  572. Shrivastava, A., D.K. Saini, and M. Pandit, Relay co-ordination optimization for integrated solar photo-voltaic power distribution grid. Cogent Engineering, 2019. 6(1): p. 1612601.
  573. Suyanto, H., M. Hafidz, and G. Alvianingsih. Transient Stability Analysis of a Hybrid Grid-Connected Battery-PV in Baubau Power System. in 2020 2nd International Conference on Industrial Electrical and Electronics (ICIEE). 2020. IEEE.
  574. Refaat, S.S., et al., Impact of grid‐tied large‐scale photovoltaic system on dynamic voltage stability of electric power grids. IET Renewable Power Generation, 2018. 12(2): p. 157-164.
  575. Jayabarathi, R., et al. Simulation and Implementation of Solar Power Penetration in an IEEE 5 bus System. in 2019 5th International Conference on Advanced Computing & Communication Systems (ICACCS). 2019. IEEE.
  576. Li, G., et al. Research on the Influence of Distributed Photovoltaics on Distribution Network Voltage in Three-phase Unbalanced State. in 2022 4th International Conference on Power and Energy Technology (ICPET). 2022. IEEE.
  577. Malouq, A.A.S. and O.G. Mrehel. Performance Study of Existing Electrical Network Connected by Large Scale Photovoltaic System. in 2022 9th International Conference on Electrical and Electronics Engineering (ICEEE). 2022. IEEE.
  578. El-Sayed, M., A. Abou El-Ela, and R.A. El-Sehiemy. Effect of photovoltaic system on power quality in electrical distribution networks. in 2016 Eighteenth International Middle East Power Systems Conference (MEPCON). 2016. IEEE.
  579. Nazifa, S., et al. Analysis of the Impact of PV Penetration in Distribution Network: A Case Study in IEEE 14 Bus System. in 2021 International Conference on Automation, Control and Mechatronics for Industry 4.0 (ACMI). 2021. IEEE.
  580. Sherzay, S. and R. Perveen. Analysis of tie grid 30 kW Solar Project. in 2021 IEEE 6th International Conference on Computing, Communication and Automation (ICCCA). 2021. IEEE.
  581. Zamri, N.D.S.M. and M.N. Abdullah, A power system analysis for large scale solar photovoltaic system using PVSyst and ETAP. Evolution in Electrical and Electronic Engineering, 2022. 3(2): p. 458-466.
  582. Makram, A., et al. Assessment of PV Penetration Impacts on Assiut International Airport Long Distribution Feeder Using Multi-Objective Performance Index. in 2021 22nd International Middle East Power Systems Conference (MEPCON). 2021. IEEE.
  583. Fokui, W.S.T., M. Saulo, and L. Ngoo. Investigating the Impact of PV Penetration on the Distribution Network: Case of Nairobi North Distribution Network. in 2021 IEEE PES/IAS PowerAfrica. 2021. IEEE.
  584. Upadhyay, T. and J.G. Jamnani, Simulation and analysis of solar photovoltaic penetration in conventional power system. Materials Today: Proceedings, 2022. 62: p. 7281-7287.
  585. Puriza, M.Y., Analysis of the feasibility of adding a grid-connected hybrid photovoltaic system to reduce electrical load. International Journal of Power Electronics and Drive Systems (IJPEDS), 2023. 14(2): p. 1160-1171.
  586. Tran, T.S., et al., Study on the impact of rooftop solar power systems on the low voltage distribution power grid: A case study in Ha Tinh province, Vietnam. Energy Reports, 2023. 10: p. 1151-1160.
  587. Iweh, C.D., et al., Assessment of the optimum location and hosting capacity of distributed solar PV in the southern interconnected grid (SIG) of Cameroon. International Journal of Sustainable Energy, 2023: p. 1-22.
  588. Kachhad, V.M. and N.M. Pindoriya. Impact assessment of APFC and solar PV on IITGN ring main distribution network. in 2020 21st National Power Systems Conference (NPSC). 2020. IEEE.
  589. Imran, M., et al., Analysis and implementation of a solar/biogas hybrid system for centralized generation at Qadirpur Ran. Energy Reports, 2022. 8: p. 13484-13493.
  590. Fokui, W.S.T., M. Saulo, and L. Ngoo, Controlled electric vehicle charging for reverse power flow correction in the distribution network with high photovoltaic penetration: case of an expanded IEEE 13 node test network. Heliyon, 2022. 8(3).
  591. Darwish, M.A.A. Design of a photovoltaic system using SAM and ETAP software. in 2021 International Conference on Green Energy, Computing and Sustainable Technology (GECOST). 2021. IEEE.
  592. Adam, S., et al. Achieving simulation as REBIANA Village Case Study of Photovoltaics System-Based Residential Distribution Grid. in 2021 10th International Conference on Renewable Energy Research and Application (ICRERA). 2021. IEEE.
  593. Turan, M.T., et al., Effect of electric vehicle parking lots equipped with roof mounted photovoltaic panels on the distribution network. International Journal of Electrical Power & Energy Systems, 2019. 109: p. 283-289.
  594. Jeelani, S.H., et al., An approach to the utilization of grid integration to analyze the performance and quality of solar photovoltaic model. Energy Reports, 2022. 8: p. 1029-1044.
  595. Kanniappen, S.M., R. Sewsunker, and I.J. Lazarus. Design Scheme for Ring-Based Extra Low Voltage Off-Grid Photovoltaic Direct Current Microgrids for Rural Electrification. in 2022 30th Southern African Universities Power Engineering Conference (SAUPEC). 2022. IEEE.
  596. Al-Adim, L., et al. Reducing the Number of Central Inverters of a Photovoltaic Plant Using Medium-Voltage Capacitor Banks. in 2022 IEEE Green Energy and Smart System Systems (IGESSC). 2022. IEEE.
  597. Dib, M., A. Nejmi, and M. Ramzi, New auxiliary services system in a transmission substation in the presence of a renewable energy source PV. Materials today: proceedings, 2020. 27: p. 3151-3156.
  598. Novoa, L. and J. Brouwer, Dynamics of an integrated solar photovoltaic and battery storage nanogrid for electric vehicle charging. Journal of Power Sources, 2018. 399: p. 166-178.
  599. Abass, A.Z. and D. Pavlyuchenko, Analysis of a gas station hybridization with a solar thermal plant by using ETAP. International Journal of Applied, 2021. 10(2): p. 118-126.
  600. Akbari Nodehi, M., Evaluation of Penetration Level of Large-Scale Photovoltaic System on Voltage Stability of Power System. International Journal of Smart Electrical Engineering, 2019. 8(01): p. 9-12.
  601. Gbadamosi, S.L., N. Nwulu, and O. Babatunde, Harmonic estimation on a transmission system with large-scale renewable energy sources. Przeglad Elektrotechniczny, ISSN, 2021: p. 0033-2097.
  602. Afifi, S. and M. Darwish. Impact of hybrid renewable energy systems on short circuit levels in distribution networks. in 2014 49th International Universities Power Engineering Conference (UPEC). 2014. IEEE.
  603. Agajie, T.F., et al., Reliability enhancement and voltage profile improvement of distribution network using optimal capacity allocation and placement of distributed energy resources. Computers & Electrical Engineering, 2021. 93: p. 107295.
  604. Acharya, S. and M. Ramezani. Transient stability assessment for generators and DER integration into the IEEE 9 Bus system. in 2020 IEEE Texas Power and Energy Conference (TPEC). 2020. IEEE.
  605. Sharif, M.S.E., et al., Design, simulation and stability analysis of wind-pv-diesel hybrid power system using etap. American Journal of Modern Energy, 2017. 3(6): p. 121-130.
  606. Vig, S. and H. Singh. Mitigation of Voltage Instability in the Hybrid Solar or Wind System using Facts Device. in IOP Conference Series: Earth and Environmental Science. 2023. IOP Publishing.
  607. Kotb, S.A., et al., Application of hybrid renewable energy for supplying the emergency power supply system in case of station blackout in nuclear power plant. Annals of Nuclear Energy, 2022. 175: p. 109222.
  608. Aref, M., et al., Modified Analytical Technique for Multi-Objective Optimal Placement of High-Level Renewable Energy Penetration Connected to Egyptian Power System. Mathematics, 2023. 11(4): p. 958.
  609. Mohamed, A.T., M.A.-H.M. Salim, and M.M. Almuhaini. Reliability assessment and feasibility study for an industrial facility with the integration of hybrid renewable energy system. in 2017 International Conference on Communication, Control, Computing and Electronics Engineering (ICCCCEE). 2017. IEEE.
  610. Iderus, S., et al., Optimization and design of a sustainable industrial grid system. Mathematical Problems in Engineering, 2022. 2022.
  611. Jahdi, S., L.L. Lai, and D. Nankoo. Grid integration of wind-solar hybrid renewables using AC/DC converters as DG power sources. in 2011 World congress on sustainable technologies (WCST). 2011. IEEE.
  612. Kuriakose, K.M., et al. Design & Development of PV-Wind Hybrid Grid Connected System. in 2019 3rd International conference on Electronics, Communication and Aerospace Technology (ICECA). 2019. IEEE.
  613. Jahdi, S., L.L. Lai, and D. Nankoo, Renewable hybrids Grid-Connection using converter interferences. International Journal of Sustainable Energy Development (IJSED), 2013. 2(1).
  614. Liu, G. Application of ETAP in distributed power supply and micro-grid interconnection. in 2019 4th International Conference on Intelligent Green Building and Smart Grid (IGBSG). 2019. IEEE.
  615. Uma, U., A. Ekwue, and E. Emelike. Fault Current Contribution from Renewable Energy Sources on Distribution Network Protection Schemes. in 2019 IEEE PES/IAS PowerAfrica. 2019. IEEE.
  616. Gómez-Ramírez, G.A. and R. Solis-Ortega. Electric Vehicle Penetration Modelling for Costa Rica Power System. in 2021 IEEE CHILEAN Conference on Electrical, Electronics Engineering, Information and Communication Technologies (CHILECON). 2021. IEEE.
  617. Yang, N.-C. and W.-C. Tseng, Adaptive three-phase power-flow solutions for smart grids with plug-in hybrid electric vehicles. International Journal of Electrical Power & Energy Systems, 2015. 64: p. 1166-1175.
  618. Waqfi, R.R. and M. Nour. Impact of PV and wind penetration into a distribution network using Etap. in 2017 7th International Conference on Modeling, Simulation, and Applied Optimization (ICMSAO). 2017. IEEE.
  619. Alimi, O.A., K. Ouahada, and A.M. Abu-Mahfouz, Real time security assessment of the power system using a hybrid support vector machine and multilayer perceptron neural network algorithms. Sustainability, 2019. 11(13): p. 3586.
  620. Oputa, O., et al., Mitigating Faults Effects on Equipment and Personnel on Substations. Journal of Science and Technology Research, 2023. 5(1): p. 101-111.
  621. Oputa, O. and T. Madueme, Fault analysis on Nigeria 330kV transmission system using etap. Nigerian Journal of Technology, 2019. 38(1): p. 202-211.
  622. Ahona, M.B., et al. Design of a 7.5 MVA Automated Substation with Fault Analysis Using ETAP Software. in 2021 5th International Conference on Electrical Engineering and Information Communication Technology (ICEEICT). 2021. IEEE.
  623. Khandelwal, T. and M. Bowman, Computer Simulation of Complex Power System Faults under various Operating Conditions. 2015.
  624. Atuchukwu John, U., Fault Analysis of Nigerian 330kV Power System. American Academic & Scholarly Research Journal, 2015. 7(4).
  625. Sankar, S.L. and M.M. Iqbal, ANSI and IEC standards based short circuit analysis of a typical 2× 30 MW thermal power plant. Middle-East Journal of Scientific Research, 2015. 23(8): p. 1617-1625.
  626. Prabhu, J.A.X., et al. Design of electrical system based on Short Circuit study using ETAP for IEC projects. in 2016 IEEE 6th International Conference on Power Systems (ICPS). 2016. IEEE.
  627. El-Ela, A.A.A., et al., Review on Active Distribution Networks with Fault Current Limiters and Renewable Energy Resources. Energies, 2022. 15(20): p. 7648.
  628. Chen, K.-L., Y.-P. Tsai, and N. Chen, Application of power current microsensors to current measurements in gas-insulated switchgears. Journal of the Chinese Institute of Engineers, 2012. 35(8): p. 1039-1049.
  629. Afifi, S., et al. Impact of DFIG wind turbines on short circuit levels in distribution networks using ETAP. in 2013 48th International Universities' Power Engineering Conference (UPEC). 2013. IEEE.
  630. Idoniboyeobu, D., et al., Analysis for Electrical Short Circuit Studies in Forcados Terminal SPDC, Nigeria, Using Per Unit Impedance Techniques.
  631. Murzintsev, A., et al., Short-circuit Current Reduction in Auxiliary Network of Traction Substations. Transportation Research Procedia, 2021. 54: p. 346-354.
  632. Tan, Z.H., et al. Short-Circuit Analyses of Parallel and Non-Parallel Transformer Operations for Railway Power Supply: A Case Study for Third Rail System. in 2020 International Conference on Smart Grid and Clean Energy Technologies (ICSGCE). 2020. IEEE.
  633. Hwang, S.-H., et al., Detectability analysis of open phase condition in Korea’s standard nuclear power plant. International Journal of Smart Grid and Clean Energy, 2019.
  634. Fani, B., E. Abbaspour, and A. Karami-Horestani, A fault-clearing algorithm supporting the MAS-based protection schemes. International Journal of Electrical Power & Energy Systems, 2018. 103: p. 257-266.
  635. Chandraratne, C., R. Naayagi, and T. Logenthiran. Smart grid protection through self-healing. in 2017 IEEE Innovative Smart Grid Technologies-Asia (ISGT-Asia). 2017. IEEE.
  636. Franco-Manrique, R., E. Gómez-Luna, and C. Ramos-Sánchez, Smart grid analysis and management in Colombia towards ETAP Real Time solution. INGENIARE-Revista Chilena de Ingeniería, 2018. 26(4).
  637. Gashi, D., et al., Network analysis for voltage regulation in Substation 35/10 [kV]“Malisheva”. IFAC-PapersOnLine, 2022. 55(39): p. 296-301.
  638. Eseosa, O. and O.S. Iroanwusi, Estimating Voltage Profiles and Power Margins in an Electric Power Network. Journal of Electrical and Power System Engineering (e-ISSN: 2582-5712), 2022. 8(3): p. 10-24.
  639. Patel, M.R., N.A. Rathod, and B. Mehta. Electrical Power Distribution Design & Voltage Profile Improvement for Metro Railway Station. in 2020 Fourth World Conference on Smart Trends in Systems, Security and Sustainability (WorldS4). 2020. IEEE.
  640. Dib, M., A. Nejmi, and M. Ramzi. Voltage Regulation of HV Grid Connected to a 40MVA Photovoltaic Power Plant. in Proceedings of the 2nd International Conference on Electronic Engineering and Renewable Energy Systems: ICEERE 2020, 13-15 April 2020, Saidia, Morocco. 2021. Springer.
  641. Bidyanath, K., S.D. Singh, and S. Adhikari, Implementation of genetic and particle swarm optimization algorithm for voltage profile improvement and loss reduction using capacitors in 132 kV Manipur transmission system. Energy Reports, 2023. 9: p. 738-746.
  642. Kiran, T.C. and N. Theivarajan. Transmission Lines main and backup fault clearance-Impact on a Nuclear Power Plant. in 2014 IEEE 2nd International Conference on Electrical Energy Systems (ICEES). 2014. IEEE.
  643. Nasef, A., A. Shaheen, and H. Khattab, Local and remote control of automatic voltage regulators in distribution networks with different variations and uncertainties: Practical cases study. Electric Power Systems Research, 2022. 205: p. 107773.
  644. Katira, M. and K. Porate. Computer Simulation of 132/11 KV Distribution Substation Using Static Var Compensator (SVC) for Voltage Enhancement-A Case Study. in 2009 Second International Conference on Emerging Trends in Engineering & Technology. 2009. IEEE.
  645. El Moursi, M., G. Joos, and C. Abbey, A secondary voltage control strategy for transmission level interconnection of wind generation. IEEE Transactions on Power Electronics, 2008. 23(3): p. 1178-1190.
  646. Hassan, A.M., T. El-Shennawy, and A. Abou-Ghazala, Modeling and Simulation of Integrated SVC and EAF using MATLAB & ETAP. 2014.
  647. Amesi, C.I., T.K. Bala, and A.O. Ibe, Impact of Network Reconfiguration: Case Study of Port-Harcourt Town 132/33kV Sub-transmission Substation and Its 33/11kV Injection Substation Distribution Networks. European Journal of Electrical Engineering and Computer Science, 2017. 1(1).
  648. Dolgicers, A., I. Zalitis, and J. Kozadajevs. The modified Seidel method as a tool for the evaluation of the stability of a power system. in 2016 IEEE 4th Workshop on Advances in Information, Electronic and Electrical Engineering (AIEEE). 2016. IEEE.
  649. Reda, A., A.F. Abdelgawad, and M. Ibrahim, Effect of non standard characteristics of overcurrent relay on protection coordination and maximizing overcurrent protection level in distribution network. Alexandria Engineering Journal, 2022. 61(9): p. 6851-6867.
Journal of Energy Management and Technology
Volume 8, Issue 3
Summer 2024
Pages 250-294

  • Receive Date 11 July 2024
  • Revise Date 15 August 2024
  • Accept Date 26 August 2024